manualshive.com logo in svg

CIRRUS DESIGN SR20, Pilot Operating Handbook

The Sealey SR20 user manual is available as a free download on our website. Gain access to step-by-step instructions and comprehensive guidance on how to operate and maintain your Sealey SR20 product. Visit manualshive.com to download the manual, ensuring optimal performance and longevity for your equipment.

Share
Download
background image

P/N 11934-003

8-11

Cirrus Design

Section 8

SR20

Handling, Servicing, Maintenance

The airplane may be moved on the ground by the use of the nose
wheel steering bar that is stowed in the rear baggage compartment or
by power equipment that will not damage or excessively strain the
nose gear assembly. The steering bar is engaged by inserting it into
lugs just forward of the nose wheel axle. 

• Caution •

While pushing the aircraft backward, the tow bar must be
installed to keep the nose wheel from turning abruptly. 

Do not use the vertical or horizontal control surfaces or
stabilizers to move the airplane. If a tow bar is not available,
use the wing roots as push points.

Do not push or pull on control surfaces or propeller to
maneuver the airplane.

Do not tow the airplane when the main gear is obstructed with
mud or snow.

If the airplane is to be towed by vehicle, do not turn the nose
wheel more than 90 degrees either side of center or structural
damage to the nose gear could result. 

1.

Refer to Airplane Three View (Section 1, Figure 1-1) and Turning
Radius (Section 1, Figure 1-2)

 or clearances. Be especially

cognizant of hangar door clearances.

2.

Insert tow bar into the lugs just forward of the nose wheel axle.

3.

Release parking brake and remove chocks

4.

Move airplane to desired location.

5.

Install chocks

6.

Remove tow bar.

To obtain a minimum radius turn during ground handling, the airplane
may be rotated around either main landing gear by pressing down on
a fuselage just forward of the horizontal stabilizer to raise the
nosewheel off the ground. 

Reissue A

Summary of Contents for SR20





























































































































































































































































































































































































































































































































Reviews:

No comments

Related manuals for SR20

Fresh Breeze Flyke Manual preview
Flyke
Brand: Fresh Breeze Pages: 17
Niviuk ICEPEAK EVOX 20 User Manual preview
ICEPEAK EVOX 20
Brand: Niviuk Pages: 26
Cessna 177 Cardinal Owner'S Manual preview
177 Cardinal
Brand: Cessna Pages: 118
Wowings Skua 1500 Construction Manual preview
Skua 1500
Brand: Wowings Pages: 21
ICARO paragliders MAVERICK 2 Manual preview
MAVERICK 2
Brand: ICARO paragliders Pages: 27
U-Turn Alpine Peak 2 L Manual preview
Alpine Peak 2 L
Brand: U-Turn Pages: 25
U-Turn FREE FORCE 3 Manual preview
FREE FORCE 3
Brand: U-Turn Pages: 32
U-Turn AFS Owner'S Manual preview
AFS
Brand: U-Turn Pages: 35
U-Turn Thriller X3 Manual preview
Thriller X3
Brand: U-Turn Pages: 38
U-Turn infinity Owner'S Manual preview
infinity
Brand: U-Turn Pages: 55
Royal-model ASH-26 Building Instructions preview
ASH-26
Brand: Royal-model Pages: 5
MODSTER AN-294994 Manual preview
AN-294994
Brand: MODSTER Pages: 28
Apogee Mini-CONDOR Manual preview
Mini-CONDOR
Brand: Apogee Pages: 8
SEMROC BlueJay KC-03 Instructions Manual preview
BlueJay KC-03
Brand: SEMROC Pages: 6
FK-Lightplanes FK 9 ELA Manual preview
FK 9 ELA
Brand: FK-Lightplanes Pages: 61
FK-Lightplanes FK 14 B Pilot Operating Handbook preview
FK 14 B
Brand: FK-Lightplanes Pages: 63
Czech Aircraft CRUISER AIRCRAFT PS-28 Cruiser 2021 Maintenance Manual preview
CRUISER AIRCRAFT PS-28 Cruiser 2021
Brand: Czech Aircraft Pages: 362

Brands by name

Popular brands

Load more brands