manualshive.com logo in svg

Chrysler PACIFICA 2018, Owner'S Manual

Share
Download
Chrysler PACIFICA 2018 Owner'S Manual Download Page 486

If the tire does not inflate to at least 26 psi (1.8 Bar)
pressure within 15 minutes:

•

The tire is too badly damaged. Do not attempt to drive
the vehicle further. Call for assistance.

If the tire inflates to the recommended pressure or is at
least 26 psi (1.8 Bar) pressure within 15 minutes:

NOTE:

If the tire becomes over-inflated, push the Deflation

Button to reduce the tire pressure to the recommended
inflation pressure before continuing.

1. Push the Power Button to turn off the Tire Service Kit.

2. Remove the speed limit label from

the Tire Service Kit and place sticker
on the steering wheel.

3. Immediately disconnect the Sealant

Hose from the valve stem, reinstall
the cap on the fitting at the end of the
hose, and place the Tire Service Kit in
the vehicle storage location. Proceed
to “Drive Vehicle.”

Drive Vehicle:

Immediately after injecting sealant and
inflating the tire, drive the vehicle
5 miles (8 km) or 10 minutes to ensure
distribution of the Tire Service Kit Seal-
ant within the tire. Do not exceed
50 mph (80 km/h).

WARNING!

Tire Service Kit is not a permanent flat tire repair. Have
the tire inspected and repaired or replaced after using
Tire Service Kit. Do not exceed 50 mph (80 km/h) until
the tire is repaired or replaced. Failure to follow this
warning can result in injuries that are serious or fatal
to you, your passengers, and others around you. Have
the tire checked as soon as possible at your authorized
dealer.

484

IN CASE OF EMERGENCY

Summary of Contents for PACIFICA 2018













































































































































































































































































































































































































































































































































































































































































































































Reviews:

No comments

Brands by name

Popular brands

Load more brands