manualshive.com logo in svg

Chrysler PACIFICA 2018, Owner'S Manual

Share
Download
Chrysler PACIFICA 2018 Owner'S Manual Download Page 370

Enabling And Disabling ParkSense

ParkSense can be enabled and disabled with the
ParkSense switch, located on the switch panel
below the Uconnect display.

When the ParkSense switch is pushed to disable the
system,

the

instrument

cluster

will

display

the

“PARKSENSE OFF” message for approximately five sec-
onds. Refer to “Instrument Cluster Display” in “Getting To
Know Your Instrument Panel” for further information.
When the gear selector is moved to REVERSE and the
system is disabled, the instrument cluster display will
show the “PARKSENSE OFF” message for as long as the
vehicle is in REVERSE.

The ParkSense switch LED will be on when ParkSense is
disabled or requires service. The ParkSense switch LED
will be off when the system is enabled. If the ParkSense
switch is pushed, and requires service, the ParkSense
switch LED will blink momentarily, and then the LED will
be on.

NOTE:

When KeySense feature is present, the ParkSense

System will reject customer input to turn the system off via
the hard switch. The instrument cluster display will show

⬙

KeySense in Use Selected Feature Cannot be Disabled

⬙

message.

Service The ParkSense Rear Park Assist System

During vehicle start up, when the ParkSense Rear Park
Assist System has detected a faulted condition, the instru-
ment cluster will actuate a single chime, once per ignition
cycle, and it will display the “PARKSENSE UNAVAIL-
ABLE WIPE REAR SENSORS” or the “PARKSENSE UN-
AVAILABLE SERVICE REQUIRED” message. Refer to “In-
strument Cluster Display” in “Getting To Know Your
Instrument Panel” for further information. When the gear
selector is moved to REVERSE and the system has detected
a faulted condition, the instrument cluster display will
show the

⬙

PARKSENSE UNAVAILABLE WIPE REAR SEN-

SORS

⬙

or

⬙

PARKSENSE UNAVAILABLE SERVICE RE-

QUIRED

⬙

message for five seconds while the vehicle is in

REVERSE. Under this condition, ParkSense will not oper-
ate and will read “OFF” over the arcs.

If “PARKSENSE UNAVAILABLE WIPE REAR SENSORS”
appears in the instrument cluster display make sure the
outer surface and the underside of the rear fascia/bumper
is clean and clear of snow, ice, mud, dirt or other obstruc-
tion and then cycle the ignition. If the message continues to
appear, see an authorized dealer.

368

STARTING AND OPERATING

Summary of Contents for PACIFICA 2018













































































































































































































































































































































































































































































































































































































































































































































Reviews:

No comments

Brands by name

Popular brands

Load more brands