manualshive.com logo in svg

Chrysler PACIFICA 2018, Owner'S Manual

Share
Download
Chrysler PACIFICA 2018 Owner'S Manual Download Page 196

•

Transmission Temperature

Displays the actual transmission temperature.

•

Oil Temperature

Displays the actual oil temperature.

•

Oil Pressure

Displays the actual oil pressure.

•

Battery Voltage

Displays the actual battery voltage.

•

Engine Hours — If Equipped

Displays the number of hours of engine operation.

Oil Life (Hold OK Button To Reset)

The “Hold OK to Reset” instruction will be displayed at all
times, but the following conditions will need to be met in
order to reset Oil Life:

•

The vehicle must be off

•

The ignition must be in the ON/RUN position

If the conditions are met, holding the

OK

button will reset

the gauge and the numeric display will return to 100%.

If the conditions are not met, a popup message will display
for 5 seconds, describing the required conditions, and then
the Oil Life screen will reappear.

Driver Assist

Push and release the

up

or

down

arrow button until the

Driver Assist display icon is highlighted in the instrument
cluster display. Refer to “Adaptive Cruise Control (ACC)
— If Equipped” in “Starting And Operating” for further
information.

Fuel Economy

Push and release the

up

or

down

arrow button until the

Fuel Economy Menu item is highlighted in the instrument
cluster display. The Fuel Economy Menu will display the
following:

•

Two sub menu pages that can be toggled between using
the

left

and

right

arrow buttons; one with Current Value

displayed and one without the Current Value displayed:

– Average Fuel Economy (MPG, L/100 km, or km/l)
– Range To Empty (miles or km)

194

GETTING TO KNOW YOUR INSTRUMENT PANEL

Summary of Contents for PACIFICA 2018













































































































































































































































































































































































































































































































































































































































































































































Reviews:

No comments

Brands by name

Popular brands

Load more brands