manualshive.com logo in svg

Chrysler PACIFICA 2018, Owner'S Manual

Share
Download
Chrysler PACIFICA 2018 Owner'S Manual Download Page 26

3. Remove the battery by sliding the battery rearward in its

pocket until the battery lifts up. Remove the depleted
battery from the battery pocket and dispose appropri-
ately.

4. Fit a new CR2032 battery ensuring that the positive (+)

side is facing upwards. Push the battery into the pocket
until it is firmly seated in place and secured under both
tabs.

5. Align the back cover into its original position and snap

it back in place by pushing it against the fob until it is
seated all around.

Programming Additional Key Fob

If you do not have a programmed key fob, contact your
authorized dealer for details.

Request For Additional Remote Controls

NOTE:

Only key fobs that are programmed to the vehicle

electronics can be used to start and operate the vehicle.
Once a key fob is programmed to a vehicle, it cannot be
programmed to any other vehicle.

CAUTION!

•

Always remove the key fobs from the vehicle and
lock all doors when leaving the vehicle unattended.

•

For vehicles equipped with Keyless Enter-N-Go —
Ignition, always remember to place the ignition in
the OFF position.

Duplication of key fobs may be performed at an authorized
dealer. This procedure consists of programming a blank
key fob to the vehicle electronics. A blank key fob is one
that has never been programmed.

NOTE:

When having the Sentry Key Immobilizer System

serviced, bring all vehicle keys with you to an authorized
dealer.

Separating The Key Fob Case

24

GETTING TO KNOW YOUR VEHICLE

Summary of Contents for PACIFICA 2018













































































































































































































































































































































































































































































































































































































































































































































Reviews:

No comments

Brands by name

Popular brands

Load more brands