manualshive.com logo in svg

Chevrolet 2010 Tahoe Police, Owner'S Manual

The Chevrolet 2010 Tahoe Police user manual is an essential resource for law enforcement officers and Tahoe owners alike. Accessible and informative, it provides comprehensive instructions and guidelines for operating this powerful vehicle. Download the free manual now from manualshive.com to unlock the full potential of your Tahoe Police model.

Share
Download
background image

Black plate (30,1)

Chevrolet Tahoe/Suburban Owner Manual - 2010

Starting the Engine

If the vehicle is a Two-mode Hybrid, see the Two-mode
Hybrid manual for more information.

Move the shift lever to P (Park) or N (Neutral). The
engine will not start in any other position. To restart the
engine when the vehicle is are already moving, use
N (Neutral) only.

Notice:

Do not try to shift to P (Park) if the vehicle

is moving. If you do, you could damage the
transmission. Shift to P (Park) only when the vehicle
is stopped.

Starting Procedure

1. With your foot off the accelerator pedal, turn the

ignition key to START. When the engine starts, let
go of the key. The idle speed will go down as the
engine gets warm. Do not race the engine
immediately after starting it. Operate the engine
and transmission gently to allow the oil to warm up
and lubricate all moving parts.

The vehicle has a Computer-Controlled Cranking
System. This feature assists in starting the engine
and protects components. If the ignition key is
turned to the START position, and then released
when the engine begins cranking, the engine will

continue cranking for a few seconds or until the
vehicle starts. If the engine does not start and the
key is held in START for many seconds, cranking
will be stopped after 15 seconds to prevent
cranking motor damage. To prevent gear damage,
this system also prevents cranking if the engine is
already running. Engine cranking can be stopped
by turning the ignition switch to the ACC/
ACCESSORY or LOCK/OFF position.

Notice:

Cranking the engine for long periods of

time, by returning the key to the START position
immediately after cranking has ended, can overheat
and damage the cranking motor, and drain the
battery. Wait at least 15 seconds between each try,
to let the cranking motor cool down.

2. If the engine does not start after 5

‐

10 seconds,

especially in very cold weather (below 0°F
or

−

18°C), it could be flooded with too much

gasoline. Try pushing the accelerator pedal all the
way to the floor and holding it there as you hold
the key in START for up to a maximum of
15 seconds. Wait at least 15 seconds between
each try, to allow the cranking motor to cool down.

3-30

Summary of Contents for 2010 Tahoe Police








































































































































































































































































































































































































































































































































































































































Reviews:

No comments

Related manuals for 2010 Tahoe Police

Daihatsu Mira Manual preview
Mira
Brand: Daihatsu Pages: 340
Federal Signal Corporation Vision SLR Quick Disconnect Manual preview
Vision SLR
Brand: Federal Signal Corporation Pages: 8
Federal Signal Corporation Vision SLR Supplement Manual preview
Vision SLR
Brand: Federal Signal Corporation Pages: 8
Feniex AM600 Instruction Manual preview
AM600
Brand: Feniex Pages: 6
Jeep 2011 grand cherokee Accessories Quick Reference Manual preview
2011 grand cherokee
Brand: Jeep Pages: 22
Jeep 2013 Grand Cherokee Owner'S Manual preview
2013 Grand Cherokee
Brand: Jeep Pages: 704
Jeep 2012 Liberty Owner'S Manual preview
2012 Liberty
Brand: Jeep Pages: 558
Xblitz G250 User Manual preview
G250
Brand: Xblitz Pages: 16
Carax HUD CRX-3001 Quick Start Manual preview
HUD CRX-3001
Brand: Carax Pages: 2
AddSecure Asset Light Installation Manual preview
Asset Light
Brand: AddSecure Pages: 14
Honda Sedan CIVIC 2022 Manual preview
Sedan CIVIC 2022
Brand: Honda Pages: 701
Prorack K577W Fitting Instructions Manual preview
K577W
Brand: Prorack Pages: 15
Toyota Solara guide Owner'S Manual preview
Solara guide
Brand: Toyota Pages: 497
PEUGEOT BOXER 2018 Handbook preview
BOXER 2018
Brand: PEUGEOT Pages: 232
STO N SHO SNS 297 Installation Procedures Manual preview
SNS 297
Brand: STO N SHO Pages: 7
SkyRack SR-CB-101 Assembly And Instruction Sheet preview
SR-CB-101
Brand: SkyRack Pages: 2
Kargo Master 408TC Installation Manual preview
408TC
Brand: Kargo Master Pages: 14
Toyota 2009 Highlander Quick Reference Manual preview
2009 Highlander
Brand: Toyota Pages: 19

Brands by name

Popular brands

Load more brands