manualshive.com logo in svg

Chevrolet 2010 Tahoe Police, Owner'S Manual

The Chevrolet 2010 Tahoe Police user manual is an essential resource for law enforcement officers and Tahoe owners alike. Accessible and informative, it provides comprehensive instructions and guidelines for operating this powerful vehicle. Download the free manual now from manualshive.com to unlock the full potential of your Tahoe Police model.

Share
Download
background image

Black plate (44,1)

Chevrolet Tahoe/Suburban Owner Manual - 2010

To shift to the Four-Wheel Drive Low position, the
ignition must be in ON/RUN and the vehicle must be
stopped or moving less than 3 mph (5 km/h) with the
transmission in N (Neutral). The preferred method for
shifting into Four-Wheel Drive Low is to have the
vehicle moving 1 to 2 mph (1.6 to 3.2 km/h). Turn the
knob to the Four-Wheel Drive Low position. You must
wait for the Four-Wheel Drive Low indicator light to stop
flashing and remain on before shifting the transmission
into gear.

Notice:

Shifting the transmission into gear before

the Four-Wheel Drive Low indicator light has
stopped flashing could damage the transfer case.
To help avoid damaging the vehicle, always wait for
the Four-Wheel Drive Low indicator light to stop
flashing before shifting the transmission into gear.

The vehicle may have significant engagement noise
and bump when shifting between Four-Wheel Drive Low
and Four-Wheel Drive High ranges or from N (Neutral)
while the engine is running.

If the knob is turned to the Four-Wheel Drive Low
position when the vehicle is in gear and/or moving, the
Four-Wheel Drive Low indicator light will flash for
30 seconds and not complete the shift unless the
vehicle is moving less than 3 mph (5 km/h) and the
transmission is in N (Neutral). After 30 seconds the
transfer case will shift to Four-Wheel Drive High mode.

Shifting Out of Four-Wheel Drive Low

To shift from Four-Wheel Drive Low to Four-Wheel Drive
High, AUTO, or Two-Wheel Drive High, the vehicle must
be stopped or moving less than 3 mph (5 km/h) with the
transmission in N (Neutral) and the ignition in ON/RUN.
The preferred method for shifting out of Four-Wheel
Drive Low is to have your vehicle moving 1 to 2 mph
(1.6 to 3.2 km/h). Turn the knob to the Four-Wheel Drive
High, AUTO, or Two-Wheel Drive High position. You
must wait for the Four-Wheel Drive High, AUTO,
or Two-Wheel Drive High indicator light to stop flashing
and remain on before shifting the transmission
into gear.

Notice:

Shifting the transmission into gear before

the Four-Wheel Drive Low indicator light has
stopped flashing could damage the transfer case.
To help avoid damaging the vehicle, always wait for
the Four-Wheel Drive Low indicator light to stop
flashing before shifting the transmission into gear.

The vehicle may have significant engagement noise
and bump when shifting between Four-Wheel Drive Low
and Four-Wheel Drive High ranges or from N (Neutral)
while the engine is running.

3-44

Summary of Contents for 2010 Tahoe Police








































































































































































































































































































































































































































































































































































































































Reviews:

No comments

Related manuals for 2010 Tahoe Police

Samsung HF1000 User Manual preview
HF1000
Brand: Samsung Pages: 133
Aries P35-2004 Installation Manual preview
P35-2004
Brand: Aries Pages: 3
Jeep Cherokee 16 1982 Technical & Service Manual preview
Cherokee 16 1982
Brand: Jeep Pages: 1311
Wagan 2227-1 User Manual preview
2227-1
Brand: Wagan Pages: 8
Thermo King T- series Driver Manual To Simple Operation preview
T- series
Brand: Thermo King Pages: 2
John Gold Gold Cruuse Cruisecontrol GC90 Installation Manual preview
Gold Cruuse Cruisecontrol GC90
Brand: John Gold Pages: 24
Whispbar K498W Fitting Instructions Manual preview
K498W
Brand: Whispbar Pages: 14
GMC 2010 Tahoe Owner'S Manual preview
2010 Tahoe
Brand: GMC Pages: 120
Prime Tech H-066 User Manual preview
H-066
Brand: Prime Tech Pages: 6
Dodge Challenger 2013 Owner'S Manual preview
Challenger 2013
Brand: Dodge Pages: 543
Skoda OCTAVIA - TECHNICAL CHANGES 11-2009 Owner'S Manual Supplement preview
OCTAVIA - TECHNICAL CHANGES 11-2009
Brand: Skoda Pages: 16
JKS JKSOGS960 Installation Instructions Manual preview
JKSOGS960
Brand: JKS Pages: 6
Oldsmobile 1995 Cutlass Supreme Owner'S Manual preview
1995 Cutlass Supreme
Brand: Oldsmobile Pages: 340
Mitsubishi Montero 1988 Manual preview
Montero 1988
Brand: Mitsubishi Pages: 367
Subaru 1999 Legacy Owner'S Manual preview
1999 Legacy
Brand: Subaru Pages: 399
Genesis GV60 2022 Quick Reference Manual preview
GV60 2022
Brand: Genesis Pages: 29
G-Tech Pro Competition User Manual preview
Pro Competition
Brand: G-Tech Pages: 180
Altius ATHUDW-SCA User Manual preview
ATHUDW-SCA
Brand: Altius Pages: 16

Brands by name

Popular brands

Load more brands