manualshive.com logo in svg

Chevrolet 2008 HHR, Owner'S Manual, Page: 324 / 430

Share
Download
Chevrolet 2008 HHR Owner'S Manual Download Page 324

{

CAUTION:

If you use bias-ply tires on your vehicle,
the wheel rim flanges could develop
cracks after many miles of driving. A tire
and/or wheel could fail suddenly, causing
a crash. Use only radial-ply tires with the
wheels on your vehicle.

If you must replace your vehicle’s tires with
those that do not have a TPC Spec number,
make sure they are the same size, load range,
speed rating, and construction type (radial
and bias-belted tires) as your vehicle’s
original tires.

Vehicles that have a tire pressure monitoring
system could give an inaccurate low-pressure
warning if non-TPC Spec rated tires are installed
on your vehicle. Non-TPC Spec rated tires
may give a low-pressure warning that is higher or
lower than the proper warning level you would
get with TPC Spec rated tires. See Tire Pressure
Monitor System on page 5-61.

Your vehicle’s original equipment tires are listed
on the Tire and Loading Information Label.
See Loading Your Vehicle on page 4-27, for
more information about the Tire and Loading
Information Label and its location on your vehicle.

5-70

Summary of Contents for 2008 HHR















































































































































































































































































































































































































































Reviews:

No comments