manualshive.com logo in svg

Chevrolet 2008 HHR, Owner'S Manual, Page: 15 / 430

Share
Download
Chevrolet 2008 HHR Owner'S Manual Download Page 15

5. Pull up on the knob

located on the top of
the seatback on
the outboard side to
release the seatback.

To raise the rear seatback(s):

{

CAUTION:

A safety belt that is improperly routed, not
properly attached, or twisted will not provide
the protection needed in a crash. The person
wearing the belt could be seriously injured.
After raising the rear seatback, always check
to be sure that the safety belts are properly
routed and attached, and are not twisted.

1. Lift the seatback up and push rearward until you

hear a click. Keep the safety belt clear of the seat
and not twisted.

The release knob on the top of the seatback has a
red ring. If the seatback is not fully latched this
ring will be visible. Push on the seatback until the
ring is not visible.

1-11

Summary of Contents for 2008 HHR















































































































































































































































































































































































































































Reviews:

No comments