manualshive.com logo in svg

Chevrolet 2008 HHR, Owner'S Manual, Page: 114 / 430

Share
Download
Chevrolet 2008 HHR Owner'S Manual Download Page 114

Shifting Out of PARK (P) (Automatic
Transmission)

This vehicle is equipped with an electronic shift lock
release system. The shift lock release is designed to:

•

Prevent ignition key removal unless the shift
lever is in PARK (P) with the shift lever button fully
released, and

•

Prevent movement of the shift lever out of PARK (P)
unless the ignition is in ON/RUN or
ACC/ACCESSORY and the regular brake pedal is
applied.

The shift lock release is always functional except in the
case of a an uncharged or low voltage (less than 9 volt)
battery.

If your vehicle has an uncharged battery or a battery
with low voltage, try charging or jump starting the
battery. See Jump Starting on page 5-38 for more
information.

To shift out of PARK (P):

1. Apply the brake pedal.

2. Then press the shift lever button.

3. Move the shift lever to the desired position.

If you still are unable to shift out of PARK (P):

1. Fully release the shift lever button.

2. While holding down the brake pedal, press the shift

lever button again.

3. Move the shift lever to the desired position.

If you still cannot move the shift lever from PARK (P),
consult your dealer or a professional towing service.

Parking Your Vehicle (Manual
Transmission)

Before leaving your vehicle, fully press the clutch pedal
down, move the shift lever into REVERSE (R), and
firmly apply the parking brake. Once the shift lever has
been placed in REVERSE (R) with the clutch pedal
pressed down, you can turn the ignition key to LOCK,
remove the key and release the clutch pedal. See
Manual Transmission Operation on page 2-31.

2-36

Summary of Contents for 2008 HHR















































































































































































































































































































































































































































Reviews:

No comments