manualshive.com logo in svg

Cedar Summit Paramount F25040, Installation And Operating Instructions Manual

Share
Download
Cedar Summit Paramount F25040 Installation And Operating Instructions Manual Download Page 96

 

96 

[email protected]

Fig. 32.2

Fig. 32.1

Step 32:  Attach Flange Assembly to Fort 

Part 1

Hardware

14 x 

#12 x 1”  Pan Screw

4 x 

#12 x 2”  Pan Screw

8 x  

#12 Screw Bezel

S7

(5 per side)

S6

A:

  With a helper place the Flange Assembly flush to the top opening in the Front Wall on Unit A as shown in fig. 

32.1, then pre-drill 1/8” pilot holes in (8935) Lower SL Insert for the 4 bottom mounting locations (approximate 

spots where circles are on figure), making sure the pre-drilled holes are a minimum of 1” deep.  (fig. 32.2)

B: 

 Attach Flange Assembly to (8935) Lower SL Insert using 4 (S7) #12 x 2” Pan Screws (with #12 Screw Bezel) 

in the pre-drilled holes.  (fig. 32.2)  Make sure the flat surfaces of the Flange Assembly are flush to (2769) Panel 

BT Frame, (2770) End Post Left and (2602) Upper Jamb as shown in fig. 32.3.

C:

  Attach the Flange Assembly flush to top of (2769) Panel BT Frame using 4 (S6) #12 x 1” Pan Screws (with 

#12 Screw Bezel) and to (2602) Upper Jamb and (2770) End Post Left using 5 (S6) #12 x 1” Pan Screws per 

side.  (fig. 32.2)

Flange 

Assembly

w/ #12 Screw 

Bezel

Top

Bottom of 

slide flush with 

(8935) Lower 

SL Insert

Top of End Wall 

opening

Outside View

Inside View

Top

S6

S6

Side

2769

w/ #12 Screw 

Bezel

S7

Flange 

Assembly

Fig. 32.3

2602

8935

2602

8935

Large Fort

Front Wall

2769

2770

Summary of Contents for Paramount F25040

















































































































































Reviews:

No comments

Brands by name

Popular brands

Load more brands