manualshive.com logo in svg

Cedar Summit Paramount F25040, Installation And Operating Instructions Manual

Share
Download
Cedar Summit Paramount F25040 Installation And Operating Instructions Manual Download Page 116

 

116 

[email protected]

Hardware

1 x 

Front Small Roof 1-1/4 x 22-9/16 x 33-5/8”

1 x 

Back Small Roof 1-1/4 x 22-9/16 x 33-3/8”

Wood Parts

2672

B:

  Place (2672) Front Small Roof against (2671) Back Small Roof so the tops form a peak then tight to the 

inside edge of the outside slats attach 1 Narrow Angle Bracket per slat with 2 (S0) #8 x 7/8” Truss Screws per 

bracket.  (fig. 47.3)

C:

  Place Small Roof Support Assembly against one side so the peaks meet and the ends of the roof supports 

are flush with the ends of the roof panels.  Attach with 6 (S11) #8 x 2” Wood Screws.  (fig. 47.3)

D:

  Attach 1 Door Roof Grill to the inside of the (2680) Roof Supports with 4 (S5) #8 x 1/2” Pan Screws.  (fig. 

47.4) 

Step 47:  Small Roof Assembly 

Part 2

6 x 

#8 x 2” Wood Screw

4 x 

#8 x 7/8” Truss Screw

4 x 

#8 x 1/2” Pan Screw

S11

2671

2672

Flush

Flush

Small Roof 

Support 

Assembly

Other Parts

2 x Narrow Angle Bracket
1 x Door Roof Grill

x 2 per 

bracket

Narrow Angle 

Bracket

Flush

Fig. 47.3

S5

S0

S0

S11

S5

Fig. 47.4

2680

2680

Door Roof 

Grill

2671

Summary of Contents for Paramount F25040

















































































































































Reviews:

No comments

Brands by name

Popular brands

Load more brands