manualshive.com logo in svg

Cedar Summit Paramount F25040, Installation And Operating Instructions Manual

Share
Download
Cedar Summit Paramount F25040 Installation And Operating Instructions Manual Download Page 36

 

36 

[email protected]

It is important to assemble the frame on a flat, smooth surface.

B:

  Place the Front/Back Wall with the diagonal supports from Step1 Part 3 between a Front/Back Wall without 

the diagonal supports and the Swing Wall without the (2778) SW Ground MODs, noticing the wall orientations.  

The tops and bottoms of the walls should be flush.   Make sure the walls are square then using the pilot holes as 

a guide pre-drill with a 3/16” drill bit and fasten the Front/Back Wall without diagonal supports to Front/Back Wall 

with diagonal supports and Front/Back Wall with diagonal support to the Swing Wall with 4 (WL5) 1/4 x 2-1/2” 

Wafer Lags per side.  (fig. 4.2)

Fig. 4.2

Hardware

WL5

Notice Front/Back 

Wall without diagonal 

supports overlaps 

Front/Back Wall with 

diagonal supports

Notice Front/Back Wall 

overlaps Swing Wall

Front/Back Wall 

without diagonal 

supports

Swing Wall

Notice slats 

to the inside

8 x 

1/4 x 2-1/2” Wafer Lag

Step 4: Large Fort Frame Assembly 

Part 2

Front/Back Wall 

with diagonal 

supports

WL5

WL5

Summary of Contents for Paramount F25040

















































































































































Reviews:

No comments

Brands by name

Popular brands

Load more brands