manualshive.com logo in svg

Cedar Summit Paramount F25040, Installation And Operating Instructions Manual

Share
Download
Cedar Summit Paramount F25040 Installation And Operating Instructions Manual Download Page 37

 

37 

[email protected]

8 x 

#12 x2” Pan Screw

2 x 

Floor Joist 1-1/4 x 3 x 40-3/4”

Wood Parts

Hardware

2608

2677

Tight

(both sides)

Fig. 4.4

Front/Back  

Wall

Swing Wall 

2677

2608

2608

2608

Flush

x 4 per 

board

End Wall

2769

2769

2769

C:

  With at least two helpers lift the two wall assemblies so the panels meet and are tight together as shown in 

fig. 4.3.

D:

  Make sure the assembly is square then on the inside of the assembly, tight to the (2769) Panel BT Frame on 

the End Wall and flush to the bottom of the panels attach 1 (2608) Floor Joist to (2677) Narrow Panel and each 

(2769) Panel BT Frame on the Front/Back and Swing Walls with 4 (S7) #12 x 2” Pan Screws per board.  (fig. 4.3 

and 4.4)

Fig. 4.3

2769

S7

S7

Step 4: Large Fort Frame Assembly 

Part 3

Summary of Contents for Paramount F25040

















































































































































Reviews:

No comments

Brands by name

Popular brands

Load more brands