manualshive.com logo in svg

Cedar Summit Paramount F25040, Installation And Operating Instructions Manual

Share
Download
Cedar Summit Paramount F25040 Installation And Operating Instructions Manual Download Page 79

 

79 

[email protected]

Warning!

 To prevent tipping and avoid potential injury, stakes must be 

driven 13” into ground. Digging or driving stakes can be dangerous if you do not 

check first for under-ground wiring, cables or gas lines. 

Step 23:  Attach Rock Wall Assembly to Fort 

Part 3

Hardware

2 x 

#12 x 2” Pan Screw

2 x Rebar Ground Stake

Other Parts

Rebar 

Ground 

Stake

S7

S7

13”

In Ground

E:

  Drive 1 Rebar Ground Stake 13” into the ground against 1 (2776) Rock Rail per assembly then attach with 1 

(S7) #12 x 2” Pan Screw per ground stake.  Be careful not to hit the washer while hammering stake into the ground 

as this could cause the washer to break off.  (fig. 23.9, 23.10 and 23.11)

F:

  After driving stake into the ground, check for sharp edges caused by the impact of the hammer.  Smooth any 

sharp edges from impact area and touch up with outdoor paint.

Fig. 23.9

Fig. 23.11

2776

2776

2776

Front Wall 

Back Wall

Fig. 23.10

Summary of Contents for Paramount F25040

















































































































































Reviews:

No comments

Brands by name

Popular brands

Load more brands