manualshive.com logo in svg

Cedar Summit Paramount F25040, Installation And Operating Instructions Manual

Share
Download
Cedar Summit Paramount F25040 Installation And Operating Instructions Manual Download Page 61

 

61 

[email protected]

Step 14:  Swing Beam Assembly

Hardware

A:

  Attach 6 Swing Hangers to the (2614) Engineered Beam using 2 (G7) 5/16 x 5-1/2” Hex Bolts (with 2 flat 

washers and 1 lock nut) per Swing Hanger as shown in fig. 14.1.

B:

  Flush to the Fort End of (2614) Engineered Beam attach 2 L-Beam Brackets with 2 (G21) 5/16 x 3-3/4” Hex 

Bolts (with 2 flat washers and 1 lock nut). (fig. 14.1 and 14.2)

C:

  Install 1 (WB7) 5/16 x 3” Wafer Bolt (with flat washer and t-nut) in the middle bolt hole in (2614) Engineered 

Beam as shown in fig. 14.3.  

IT IS IMPORTANT THAT THIS BOLT IS ATTACHED.  IT WILL MINIMIZE 

CHECKING OF WOOD.

D: 

 Attach Cedar Summit Plaque to centre of (2614) Engineered Beam (over top of t-nut) using 4 (S18) #6 x 1” 

Wood Screws. (fig. 14.4)

Other Parts

Wood Parts

1 x 

Engineered Beam 4 x 6 x 88”

 

Swing End

Fort End

Fort End

WB7

Fig. 14.1

Fig. 14.3

Fig. 14.2

2614

2614

2614

FW2

12 x 

5/16 x 5-1/2” Hex Bolt (5/16” flat washer x 2, 5/16” lock nut)

2 x 

5/16 x 3-3/4” Hex Bolt (5/16” flat washer x 2, 5/16” lock nut)

1 x 

5/16 x 3” Wafer Bolt (5/16” flat washer & 5/16” t-nut)

4 x 

#6 x 1” Wood Screw

6 x Swing Hangers
2 x L-Beam Bracket
1 x Cedar Summit Plaque

G21

S18

G7

WB7

Swing Hanger x 6

L-Beam 

Bracket

x 4

Flush

L-Beam 

Bracket

Cedar Summit 

Plaque

2614

TN2

G21

FW2

LN2

FW2

LN2

FW2

G7

Fig. 14.4

S18

Summary of Contents for Paramount F25040

















































































































































Reviews:

No comments

Brands by name

Popular brands

Load more brands