manualshive.com logo in svg

Cedar Summit Paramount F25040, Installation And Operating Instructions Manual

Share
Download
Cedar Summit Paramount F25040 Installation And Operating Instructions Manual Download Page 1

INSTALLATION AND OPERATING INSTRUCTIONS

PARAMOUNT – F25040

Rev 02/04/2016

9405040

Table of Contents

Warnings and Safe Play Instructions  .  .  .  .  .  .  .  .  .  . pg . 2
Protective Surfacing Guidelines .  .  .  .  .  .  .  .  .  .  .  .  .  .  . pg . 3
Instructions for Proper Maintenance  .  .  .  .  .  .  .  .  . pg . 4
About Our Wood – Limited Warranty  .  .  .  .  .  .  .  .  . pg . 5
Keys to Assembly Success  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  . pg . 6
Part ID  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  . pg . 8-20
Step-By-Step Instructions  .  .  .  .  .  .  .  .  .  .  .  .  .  .pg . 21-141
Installation of I .D ./Warning Plaque  .  .  .  .  .  .  .  . pg . 142
Registration  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .Last  Page

Cedar Summit

c/o ©Solowave Design L .P .

Mount Forest, ON Canada

N0G 2L0
www .cedarsummitplay .com

support@cedarsummitplay .com

Customer Service

1-877-817-5682 (toll free) 

1-519-323-2258

To reduce the risk of serious injury or death, you must read and 

follow these instructions. Keep and refer to these instructions 

often and give them to any future owner of this play set. 

Manufacturer contact information provided below.

OBSTACLE FREE SAFETY ZONE -36’ 9” x 27’ area requires Protective Surfacing. See page 3. 

MAXIMUM VERTICAL FALL HEIGHT - 6’ 7” 

CAPACITY - 15 Users Maximum, Ages 3 to 10; Weight Limit 110 lbs. (49.9 kg) per child.
RESIDENTIAL HOME USE ONLY. Not intended for public areas such as multi-unit residences, schools, churches, 

nurseries, day cares or parks.

WARNING

2-4 Hrs

Two person

assembly

TUBE SLIDE

20-24 Hrs

Two person

assembly

FORT

24'-8"

36'-9"

27'-0"

12'-7"

PARAMOUNT H: 11 FT.

Summary of Contents for Paramount F25040

















































































































































Reviews:

No comments

Brands by name

Popular brands

Load more brands