EN
EN
DIGIWAY Plus
Inward or Outward Door Operator
27
Advanced Setting
Ex Power Close
Enable / Disable
When enabled, adds one more
When enabled, adds one more CLOSING
CLOSING pulse after the regular CLOSING cycle to compensate
pulse after the regular CLOSING cycle to compensate
possible friction or door imbalance.
possible friction or door imbalance.
Enable or disable this function with the UP or DOWN buttons and confirm with OK
Enable or disable this function with the UP or DOWN buttons and confirm with OK
Default value = DISABLE
Default value = DISABLE
11)
11)
Advanced Setting
Extra Close Time
Extra Close Time
|||||||||||||||||.........0 SEC.
This function allows to set the duration
This function allows to set the duration TIME
TIME of the
of the CLOSING
CLOSING extra pulse.
extra pulse.
Change the value by pressing the UP or DOWN buttons and confirm with OK.
Change the value by pressing the UP or DOWN buttons and confirm with OK.
Default value = 0 SEC
Default value = 0 SEC
13)
13)
Advanced Setting
Fire Release
Fire Release
Open/Free/Closed
When the Fire Release function is enabled, it’s possible to set the reaction of the door depending on
When the Fire Release function is enabled, it’s possible to set the reaction of the door depending on
the failure of the Fire power (V+, V-):
the failure of the Fire power (V+, V-):
•
• DOOR FREE
DOOR FREE
= In case of
= In case of Fire Power
Fire Power failure the door becomes FREE (System Off)
failure the door becomes FREE (System Off)
•
• DOOR OPEN
DOOR OPEN
= In case of
= In case of Fire Power
Fire Power
failure the door opens and stays OPEN until the fire power
failure the door opens and stays OPEN until the fire power
is reset or the function of the
is reset or the function of the
Menu Configuration is disabled.
Menu Configuration is disabled.
•
• DOOR CLOSED LOCKED
DOOR CLOSED LOCKED
= Door CLOSED and lock active
= Door CLOSED and lock active
•
• DOOR CLOSED UNLOCKED
DOOR CLOSED UNLOCKED
=
= Door CLOSED and lock disactive
Door CLOSED and lock disactive
14)
14)
Advanced Setting
Max Obst Cycles
Max Obst Cycles
|||||||||||||||||.............000
When the door meets an obstacle during closing, it re-opens immediately. At the end of the pause
When the door meets an obstacle during closing, it re-opens immediately. At the end of the pause
time, it re-closes. If the obstacle is still present the cycle restarts.
time, it re-closes. If the obstacle is still present the cycle restarts.
This parameter sets the max number of re-closing attempts before stop and wait for an external
This parameter sets the max number of re-closing attempts before stop and wait for an external
command. Range : from
command. Range : from
1 to 256
1 to 256
.
. Value 0 of the parameter means no limit.
Value 0 of the parameter means no limit.
Default value = 100 attempts
Default value = 100 attempts
15)
15)
Advanced Setting
Ex Close Torque
Ex Close Torque
|||||||||||||||||...................
50 %
This function allows to set the
This function allows to set the TORQUE
TORQUE of the
of the CLOSING
CLOSING extra pulse
extra pulse.
.
Change the value by pressing the UP or DOWN buttons and confirm with OK.
Change the value by pressing the UP or DOWN buttons and confirm with OK.
Default value = 50%
Default value = 50%
12)
12)
Advanced Setting
OD on Closing
OD on Closing
Reopen
16)
16)
After the detection of an obstacle during the closing the door will react in different way, according to
After the detection of an obstacle during the closing the door will react in different way, according to
the following settings:
the following settings:
•
• Reopen: The door reopens and after the pause time recloses
Reopen: The door reopens and after the pause time recloses
•
• Stop & Wait: The door stops and after the pause time recloses
Stop & Wait: The door stops and after the pause time recloses
•
• STOP: The door stops and waits for a command to reopen and for a further command
STOP: The door stops and waits for a command to reopen and for a further command
to reclose.
to reclose.
