However, if the extension is given only Local dialing facility, then it cannot dial STD numbers of the Memory.
Entering Telephone Numbers in the memory
Dial #
0000 + 46 CC NN
….. #
Where, CC = Memory Code number from 01 to 48.
NN = Telephone Number of maximum 16 digits.
Deleting Memory Codes
Dial #
0000 + 46 CC # to delete a particular Memory Dialing Code.
Where, CC = Memory Code number from 01 to 48.
Dial #
0000 + 46 # to delete all Memory Dialing Codes.
Operation from SLT
Dial # 70 + CC = Memory Code number from 01 to 48
Allow / Disallow Memory Dialing to Selected Extensions
To allow memory dialing to an Extension, use
“Allowed Table” program as given below:
Dial #
0000 + 40 NN L # (L should be = 0 and NN= Last 2 Digits of the Original Extension Number)
Dial #
0000 + 43 01 1 # (With this program 1 digit is entered in location 01 of Allowed Table)
To disallow memory dialing to an Extension, use
“Junction Dialing Control” program as given below:
Dial #
0000 + 40 NN L # (L should be = 6 and NN= Last 2 Digits of the Original Extension Number)
Note:
In special software versions which have “Memory Dialing to All”, the code to disallow dialing to all is 446# and then
Memory dialing through #70CC can be done by all the Extensions.
.
Operator Extension Setting
.
In default there are 2 Operator Extensions in the system.
Operator Extensions can be changed as described below:
To change the first Operator Extension, Dial #
0000 + 150NN#
Where, NN = Last 2 digits of Extension which is to be made the first Operator.
To change the second Operator Extension, Dial #
0000 + 151NN#
Where, NN = Last 2 digits of Extension which is to be made the second Operator.
Note:
If only one Extension (Say603) is to be used as Operator then enter code: 15003# 15103#
When both Operator extensions are busy and another Junction call lands on it, a warning tone is heard by the Operator.
During this time dial FLASH #9.
The 2
nd
Call will get connected & the 1
st
Call will go on Hold.
Now, if required to talk to the first call then dial Flash + #9
To disconnect any of the 2 calls, keep handset down while talking to that Junction line.
Similarly 3
rd
Junction call can also be picked by the Operator by dialing Flash + #9. When 3 Calls are picked by Operator
and put on Hold, then on dialing Flash + #9 the first call on Hold will get retrieved first.
Operator access code 0 cancellation
In default Operator can be accessed by dialing 0. If this single digit access code is to be cancelled then dial #
0000 +
1521#.
To enable the same, dial #
0000 + 1520#.
.
Paging
.
The PBX can be connected to an External Paging Amplifier/Speakers. Then paging can be done from any extension by dialing #86
Refer heading “Installation” for connections.
.
Password
.
There is only one Password for the whole PBX programming and this Password can be changed by the user. The default
Password is 0000.
Process to change the Password
:
#
0000 + 09xxxx#
Here, 0000 = Default password
xxxx = New Password
.
Redial
.
To redial Telephone number on Junction Line, Dial 9 + Telephone Number
Get Engaged Tone
Press “Redial” key on the SLT Telephone set.
.
Remote Programming
.
The PBX can be programmed by a caller while talking to any of the 4 extensions (601, 602, 603 or 604) through a Junction
Line.
Procedure
:
Caller (Say A) calls on Junction line of the PBX and is talking to Extension 601(Say B).
During communication, B presses FLASH - #0. At this time, if 3 beep tones are received then repeat the process of
FLASH-#0.
Now A dials the 4 digits of the PBX password (Do not dial #
before the PW) & starts doing the required
programming. During B should not hang up. When B hangs up, the call is disconnected.
