The access to each Extension can be different in Day mode and Night mode.
Procedure
:
Dial #
0000 + 70 J NN X # (For Day Mode access)
Dial #
0000 + 71 J NN X # (For Night Mode access)
Where, J = 01, 02 ,03 or 04 representing the 1
st
, 2
nd
, 3
rd
& 4
th
Junction Line.
NN = Last 2 Digits of Extension Number
X = 0 to allow Junction access
1 to Disallow Junction access.
Dial #
0000 + 70 J X # (To allow/disallow all exte
nsions to access “J” Junction in Day Mode)
Dial #
0000 + 70 NN 2 # (To allow “NN” extension to access all Junctions in Day Mode)
Dial #
0000 + 70 NN 3 # (To disallow “NN” extension to access all Junctions in Day Mode)
Dial #
0000 + 71 J X # (To
allow/disallow all extensions to access “J” Junction in Night Mode)
Dial #
0000 + 71 NN 2 # (To allow “NN” extension to access all Junctions in Night Mode)
Dial #
0000 + 71 NN 3 # (To disallow “NN” extension to access all Junctions in Night Mode)
.
Junction Dialing Controls
.
Junction dialing facility can be controlled Extension wise as below
:
Dial #
0000 + 40 NN L #
where, NN= Last 2 digits of Extension number.
L = 0 -
The Extension can dial only the numbers starting with digits defined in “Allowed Table”
1 - The Extension can dial all numbers.
2 - The Extension can dial all numbers except for ISD numbers.
3 - The Extension can dial all numbers except for STD numbers.
4 -
The Extension can dial all numbers except for the numbers starting with digits defined in “Denied
Table-
A”
5 -
The Extension can dial all numbers except for the numbers starting with digits defined in “Denied
Table-
B”
6 - The Extension cannot dial out but can make internal calls.
To give all extensions the same L value:
Dial #
0000 + 40 L #
Note:
In default: all extensions are in L = 1 mode.
:
In case of 16120S, extensions from 6100 to 6120 can be programmed only through Computer.
.
Junction Call Hold + Tr Making multiple calls
.
To transfer a Junction line to another extension, FLASH and dial the Extension number while talking on the junction line.
Now there can be following 4 conditions:
1. When called extension lifts, calling extension can converse and then keep the Handset down. The Junction call will
then get transferred.
2.
Called extension lifts but doesn’t want to talk then he may keep the Handset down.
The call will come back to the transferring extension.
3. The called extension is ringing but not lifting the Handset. Keep the Handset down.
The call will ring on the called extension for 25 secs and if not answered it will ring back on the transferring extension.
Now if the Transferring extension is busy, the Junction call will be disconnected by the PBX.
If the user wants to disable this auto call back in case of No Answer while transferring a Junction call, program as
below
:
Dial #
0000 + 163 # (Now the Junction call will disconnect if the called extension does pick the call within 25 secs)
To shift back to auto call back mode
:
Dial #
0000 + 162 #
4. If the called Extension is engaged, the user will hear 2 tones. Now FLASH to get back to the Junction line. If FLASH is
not done within 10 secs, the Junction line will get connected. This is the default setting in the PBX.
Alternately the user can change to the following mode
:
On dialing an engaged extension user would get engaged tone. During the engaged tone user can FLASH and get
connected to the Junction line.
Programming
:
Dial #
0000 + 1531 #
To shift back to the default setting, Dial #
0000 + 1530 #
Making two or more Junction calls from SLT
While talking on one Junction line,
FLASH
Dial ## - To park the call
Dial 9 to take another Junction
Dial the required Telephone number
FLASH
Dial ## - To retrieve the first parked call
Similarly, more calls can be made.
.
Junction Dialing Delay Time
.
This is the time after the last digit dialed by an extension on Junction Line.
