Incoming Junction Call ringing
Parked Call
Junction Call on Hold
Door Phone Call
Internal Call
Call Parking Hold time can be changed through the following program
:
Dial #
0000 + 186 TT # Where, TT= 01 to 99. (01 means 10 Secs and 99 means 990 secs)
In default the value is 12 i.e., 120 secs.
.
Checking Extension PBX Version
.
To know the extension number of an extension or PBX date or PBX time, do the following
:
From SLT extension having CLI Telephone Set
Dial # 62 and keep the handset down.
The extension will ring and its number shall be displayed on the CLI phone. The display may show a 7 digits
number. In that case the last 4 digits would be the Extension number.
Dial # 64
– To see the
PBX version
From SLT extension having Telephone Set w/o CLI
Dial # 60
– to know the last 2 digits
Hear tones denoting 2 digits of Extension number.
Example
:
If the extension number is 6001, you will hear 10 Tones and then 1 Tone with a gap of 1.5 secs.
10 Tones indicate 0 and 1 Tone indicates digit 1.
Dial # 61
– to know the last 3 digits
Hear tones denoting 3 digits of Extension number.
Example
:
If the extension number is 6001, you will hear 6 Tones, 10 Tones, 10 Tones and then 1 Tone with a
gap of 1.5 secs.
6 Tones indicate digit 6. 10 Tones indicate digit number 0 and 1 Tone indicates digit 1.
.
CLI (Calling Line Identification)
.
The incoming Junction call telephone number is displayed on the LCD of the CLI phone on which the defined Junction call
rings. This feature will work with Telephones having CLI feature.
.
CLI Transferable / Internal CLI
.
When a Junction call is transferred from an extension to another extension, the external telephone number is displayed on
the LCD of the CLI phone. When an extension calls another extension, Extension number is displayed on the LCD of the
CLI phone.
.
CLI
– Digits addition
.
Some CLI Telephones cannot display less than 4 digit numbers. In that case if the PBX extension numbers are less than 4
digits then additional dummy numbers need to be added by the PBX.
Procedure
:
Dial #
0000 + 180 KK #
Where KK = Any 2 digit
To Disable, dial #
0000 + 180 #
.
CLI Receiving Mode (DTMF / FSK / Auto)
.
The system senses CLI on Junction lines in DTMF mode or FSK mode or it can be programmed in auto mode to detect
either of the two.
Procedure
:
Dial #
0000 + 1812 # - for FSK mode
Dial #
0000 + 1813 # - for DTMF mode
Dial #
0000 + 1814 # - for Auto Detection mode
Dial #
0000 + 1815 # - for always FSK & DTMF mode
Default: Auto Detection mode.
.
CLI Transmitting Mode (DTMF / FSK)
.
The PBX generates CLI on Extensions in FSK mode in default.
For other modes, program is
:
Dial #
0000 + 1811 # - for DTMF mode
Dial - Dial #
0000 + 1810 # for FSK mode
.
Cold Start
.
To put the PBX ON in battery mode when mains AC is not present, push the PBX power Switch to ON position and press a push switch
with the help of a pin. There is a hole provided at the bottom of the PBX. Insert a pin and pull then pull it to your side. You will hear a
click sound and the PBX will get ON.
.
Computer Connectivity
– for Call Logging & Call Voice Recording
.
The PBX can be connected to a PC by installing optional “PC Interface Card”. PBX is connected to the PC through a “RJ to RS232
Le
ad” (explained under the heading “Installation”).
A software is loaded in the PC which can work in the back ground while it is being used for other applications.
