Some or all extensions can be programmed to get Junction Line on lifting the Handset.
To dial internal numbers, dial
on lifting the Handset. You will get internal dial tone of the PBX.
To program an extension to get a free Junction line on lifting handset,
Dial #
0000 + 2 NN 0 #
Where, NN= last 2 digits of Extension numbers that is to be programmed for Direct Junction Access.
Dial #
0000 + 20 # -
To convert all Extensions in “Hot Line to Junction” mode
Dial #
0000 + 2 NN 1 # - To convert NN Extension in normal mode.
Dial #
0000 + 21 # - To convert all Extensions in normal mode.
Note
:
When all Extensions are converted to Hot Line then to get into the Programming mode, lift Handset
– dial
#
0000
+ whatever Programming to be done.
.
Hot Line to Extension
(only in 432S)
.
Some or all extensions can be programmed to get connected to an Extension, on lifting the Handset.
To dial internal numbers, dial
on lifting the Handset. You will get internal dial tone of the PBX.
To program an extension in this mode,
Dial #
0000 + 883 NN #
Where, NN= last 2 digits of Extension numbers that is to be programmed for this feature.
Dial #
0000 + 883 # - To c
onvert all Extensions in “Hot Line to Junction” mode
Dial #
0000 + 884 NN # - To convert NN Extension in normal mode.
Dial #
0000 + 884 # - To convert all Extensions in normal mode.
Note
:
When all Extensions are converted to Hot Line then to get into the Programming mode, lift Handset
– dial
#
0000
+ whatever Programming to be done.
.
Hotel / Office Version
.
The PBX can be operated in either Hotel version of Office version. In default, it is in Office Version.
In Hotel Version, PBX has to be connected to a PC whereby following features get activated
:
Check-In
Check-Out
Call Cost Calculation
Balance Amount of Extension (If an Extension doesn’t have balance then its dialing will not be opened on Check-In)
When PC is connected to PBX, all the stored calls in PBX get transferred to PC and then get deleted from the PBX
memory. The PBX has memory to store call records of up to 3,000 calls.
To connect PC to the PBX, an optional PC Interface card is to be installed in the PBX.
Programming:
To Change the PBX to Hotel Version, Dial #
0000 + 8850#
To change to Office version, Dial #
0000 + 8851#
.
Junction Access During Power Failure
.
This is an optional feature and is activated
only when “DG NF” is installed.
With this feature, when the system is switched OFF, the Junction lines get directly connected to desired extensions.
.
Junction Access Code / Change
.
Junction lines can be accessed in rotation by dialing 9.
To access a particular Junction line, dial #101, #102 to #116 (101 represents the first junction Line and 116 the 16th).
The Junction access code 9 can be changed to 0.
To change the Junction access code from 9 to 0:
First remove the Operator Access Code 0 (Refer heading “
Operator Extension setting”).
Then program as below
:
Dial #
0000 + 0000 X #
Where, X= Junction Access Code (0 to 9). If it is 0 then Junction access code will be 0 and the Operator code = 9.
If it is 9 then Junction access code will be 9 and the Operator code = 0.
If it is 2 then Junction access code will be 2 and the Operator code = 0 as well as 9.
This is true for X = 1 to 8.
.
Junction Access in Circular / Sequential Mode
.
In case of dialing out on the Junction Lines, PBX can be configured to work in either of the following 2 modes:
Mode Description
Circular When an extension dials 9, the PBX will allot Junction numbers 01.
Next time any Extension dial 9, Junction number 02 will be allotted. Then 03. Then 01.
Sequential When an extension dials 9, the PBX will allot Junction numbers 01.
Next time any Extension dial 9 and if Junction 01 is free then Junction 01 will be allotted. Junction
number 02 will be allotted only when Junction 01 is engaged.
Programming
:
To program in Circular mode, Dial #
0000 + 0620 #
To program in Sequential mode, Dial #
0000 + 0621 #
.
Junction Access Control
.
Every Extension can be programmed to access one or all of the 3 Junction Lines.
