#
0000 + 3X J # This program
disables the default ring assignment
.
#
0000 + 3 X J NN 0 # Here, X= 0 for Day Mode and 1 for Night mode.
J = 01 to 16 (Junction Line no)
NN = Last 2 digits of the 1
st
Round Robin Extension No.
(Not the Flexible Number)
Also note that the first Extension in Round Robin can be 601 to 616 only.
Cannot program Extension 617 to 632 in case of 432S.
# 27 NN XXX Where, XXX= 2
nd
Extension number of Round Robin Extensions. If flexible numbering is done then
enter the Flexible number.
If the Flexible number is say 26 then XXX will be = 26 & not
026.
NN= The last 2 digits of the
1st Extension number (Not the flexible number
)
# 27 NN XXX Where, XXX= 3rd Extension number of Round Robin Extensions. If flexible numbering is done then
enter the Flexible number.
If the Flexible number is say 26 then XXX will be = 26 & not
026.
NN= The last 2 digits of the
2nd Extension number (Not the flexible number
)
# 27 NN XXX Where, XXX= 4th Extension number of Round Robin Extensions. If flexible numbering is done then
enter the Flexible number.
If the Flexible number is say 26 then XXX will be = 26 & not
026.
NN= The last 2 digits of the
3rd Extension number (Not the flexible number
)
Note
:
Round Robin Ring Assignment can be set in combination with Simultaneous Ring i.e., some extension would ring in
Simultaneous mode and some in Round Robin mode for the same Junction Line ring.
:
The Round Robin for Internal Calls can be Enabled / Disabled through the following Program:
#
0000 + 178 # to Enable
#
0000 + 179 # to Disable
Example:
To assign Round Robin to 6001, 6002, 6004 and then 6003
Dial #
0000 + 3 0 0 1 #
#
0000 + 3 0 0 1 01 0 #
#27 01 6002
#27 02 6004
#27 04 6003
Dial #
0000 + 3 0 0 2 #
#
0000 + 3 0 0 2 01 0 #
#27 01 6002
#27 02 6004
#27 04 6003
Dial #
0000 + 3 0 0 3 #
#
0000 + 3 0 0 3 01 0 #
#27 01 6002
#27 02 6004
#27 04 6003
Options when all assigned extensions are busy
When the extensions assigned for the Junction incoming call are busy, following options can be set:
Dial #
0000 + 1880 (The assigned extension when busy, will hear a waiting call beep after every 5 seconds)
This is the default setting.
Dial #
0000 + 1881#
(The call will land on the first available extension starting from 601, 602, …to … 632)
.
Junction Line - Enable / Disable
.
Procedure to enable or disable Junction Line
:
To Enable one Junction Line at a time, Dial #
0000 + 060 J #
Here, J = 01, 02, 03 to 16 representing the 16 Junction Lines
To Disable one Junction Line at a time, Dial #
0000 + 061 J #
Here, J = 01, 02, 03 to 16 representing the 16 Junction Lines
To disable all the 4 Junction Lines,
Dial #
0000 + 0610 #
To enables all the Junction Lines,
Dial #
0000 + 0600 #
Note
:
If all Junction Lines are enabled with “Dial #
0000 + 0600 #” then the programming “Dial #
0000 + 060 J #” will not
work unless all the Junction lines are disabled.
:
In default all Junction Lines are Disabled.
.
LCR (Least Call Routing)
– Manual
.
This feature allows the user to dial out telephone numbers through the cheapest Junction line.
In this mode, the user can pick particular Junction lines (called Special Junctions) to make Junction calls.
For Programming procedure
refer “Junction Grouping”
.
Memory Dialing
.
The PBX has memory for 48 Telephone numbers that can be dialed from an extension by dialing 2 digit codes.
