Cayman Systems 2E-H-W User Manual Download Page 14

Page: 14 / 170

About Your Cayman 2E-H-W

Cayman 2E-H-W User’s Guide

1-4

November 2000

Cayman 2E-H-W
Front Panel

The front panel of your Cayman 2E-H-W (Figure 1-1) includes the
following LEDs and ports.

Figure 1-1

Cayman 2E-H-W Front Panel

The

power LED

remains steadily on when you connect your

Cayman 2E-H-W to a power supply.

The

wireless LED

flashes when a packet is sent or received

over the wireless network port.

Eight 10BaseT Ethernet hub ports lets you connect network
devices within a workgroup. Each hub port has an

integrated

LED

that remains on when the Cayman 2E-H-W is connected to

the device and that flashes when a packet is sent or received
over the associated hub port.

The

WAN LED

flashes when a packet is sent or received over the

wide area network (WAN) Ethernet port.

Summary of Contents for 2E-H-W











































































































































































Search results

Summary of Contents for 2E-H-W

Reviews:

Related manuals for 2E-H-W

Brands by name

Popular brands

Cayman Systems 2E-H-W, User Manual

Search results

Summary of Contents for 2E-H-W

Reviews:

Related manuals for 2E-H-W

Brands by name

Popular brands