Cayman Systems 2E-H-W User Manual Download Page 57

Page: 57 / 170

Cayman 2E-H-W User’s Guide

Configuring Your Cayman 2E-H-W

November 2000

3-35

Figure 3-14

SNMP Setup Window

To configure the SNMP settings for your Cayman 2E-H-W:

Enter information about the system contact in the

System

Contact

field.

For example, you might enter the name, phone number, beeper
number, or email address of the person responsible for the
Cayman 2E-H-W.

Enter information about the system location in the

System

Location

field.

For example, you might enter the building, floor, or room
number where the Cayman 2E-H-W is located.

Click the

Save

button to store your modified

configuration in the Cayman 2E-H-W memory.

If you want the Cayman 2E-H-W to use authentication
traps, click the

Authentication Traps On

radio button.

If SNMP trapping is enabled, your Cayman 2E-H-W sends
authentication traps to all SNMP trap destinations. You must

Summary of Contents for 2E-H-W











































































































































































Search results

Summary of Contents for 2E-H-W

Reviews:

Related manuals for 2E-H-W

Brands by name

Popular brands

Cayman Systems 2E-H-W, User Manual

Search results

Summary of Contents for 2E-H-W

Reviews:

Related manuals for 2E-H-W

Brands by name

Popular brands