Cayman Systems 2E-H-W User Manual Download Page 46

Page: 46 / 170

Configuring Your Cayman 2E-H-W

Cayman 2E-H-W User’s Guide

3-24

November 2000

Use the

Admin Restrictions

list to specify whether the

Cayman 2E-H-W accepts administrative commands
received over the WAN port.

Options are:

None

– All traffic is accepted over this port.

Admin-Disabled

– Router traffic is accepted over this port

but administration commands are ignored.

Click the

Save

button to store your modified

configuration in the Cayman 2E-H-W memory.

10. Click the

Restart Cayman-2E

button on the Cayman

2E-H-W Home Page to restart your Cayman 2E-H-W with
its new configuration.

Configuring
Password
Settings

You can establish different levels of access security to protect your
Cayman 2E-H-W settings from unauthorized display or modification.

Admin level access

lets you display and modify all settings in

the Cayman 2E-H-W.

User level access

lets you display (but not change) settings in

the Cayman 2E-H-W. You must assign the Cayman 2E-H-W an
Admin password before you can assign it a User password.

You will see a warning on the Cayman 2E-H-W configuration screens
until you set an administrative password.

To prevent anyone from observing the password you enter,
characters in the old and new passwords are not displayed as you
type them.

Passwords go into effect immediately. You do not have to restart the
Cayman 2E-H-W for the password to take effect. Assigning a
password to a Cayman 2E-H-W does not affect communications
through the device.

Summary of Contents for 2E-H-W











































































































































































Search results

Summary of Contents for 2E-H-W

Reviews:

Related manuals for 2E-H-W

Brands by name

Popular brands

Cayman Systems 2E-H-W, User Manual

Search results

Summary of Contents for 2E-H-W

Reviews:

Related manuals for 2E-H-W

Brands by name

Popular brands