Case 721G Stage IV Operator'S Manual Download Page 94

Page: 94 / 522

3 - CONTROLS AND INSTRUMENTS

Seat depth adjustment

Lift handle up and move the cushion to the desired posi-
tion. Release the handle to lock the cushion in place.

LEIL17WHL1488AB

Seat cushion angle adjustment

Lift up on the handle and move the seat to the desired
angle. Release the handle to lock the cushion angle.

LEIL17WHL1489AB

Backrest adjustment

Lift up the handle and move the backrest to the desired
position. Release the handle to lock in position.

LEIL16WHL1399AB

Armrest angle adjustment

Turn the knob to raise or lower the armrest to the desired
position.

LEIL16WHL1400AB

3-10

Summary of Contents for 721G Stage IV











































































































































































































































































































































































































































































































































Search results

Summary of Contents for 721G Stage IV

Reviews:

Brands by name

Popular brands

Case 721G Stage IV, Operator'S Manual

Search results

Summary of Contents for 721G Stage IV

Reviews:

Brands by name

Popular brands