background image

2 - SAFETY INFORMATION

Utility safety

WARNING

Electrical shock hazard!
Do not work under overhangs or electric wires. Do not work where there is a danger of sliding.
Failure to comply could result in death or serious injury.

W0215A

Safety precautions must be followed when working near
buried and overhead utility lines.

During operation it is likely that you will be working around
or near buried or overhead utility lines which may include,
but are not limited to:

• Electrical power line

• Gas line

• Water line

• Communication line - telephone or cable television

• Sewer line

NOTICE:

before beginning any machine operation, it is

your responsibility to be aware of all such utility lines
buried and overhead in the area of your project and to
avoid them.

Always have all local utility companies mark the location
of their lines.

NOTICE:

check with local authorities for laws, regulations

and/or strict penalties requiring you to locate and avoid
existing utilities.

Call all local utility companies before you
perform any machine operation

Know the utility color code:

Electric

Red

Gas, oil, or petroleum

Yellow

Communication,
telephone, television

Orange

Water

Blue

Sewer

Green/Brown

Proposed excavation

White

Surveying

Pink

Reclaimed water and slurry

Purple

After locating any buried utility lines, carefully dig a hole
by hand and/or automatic vacuum equipment to the utility
line to verify the location and depth of the line.

RCPH10WHL001BAH

1

2-14

Summary of Contents for 721G Stage IV











































































































































































































































































































































































































































































































































Reviews:

Related manuals for 721G Stage IV