manualshive.com logo in svg

Case 721G Stage IV, Operator'S Manual

Share
Download
Case 721G Stage IV Operator'S Manual Download Page 324

7 - MAINTENANCE

Drive belt - Check

WARNING

Entanglement hazard!
Always stop the engine and engage the parking brake, unless otherwise instructed in this manual,
before checking and/or adjusting any drive belt or chain.
Failure to comply could result in death or serious injury.

W0097A

WARNING

Moving parts!
Install all covers, panels, and guards after servicing or cleaning the machine. Never operate the ma-
chine with covers, panels, or guards removed.
Failure to comply could result in death or serious injury.

W0135A

Check the drive belt for correct tension, wear and damage every 250 hours. Wrong belt tension may cause battery
charge failure, engine overheating, or belt wear.

Prior operation:

Keep all non-authorized personnel clear of the area. Park the machine on a firm, level surface in neutral with the
parking brake applied. Lower the bucket/attachment to the ground. Turn off the engine. Install the transport/service
link into the locked position.

NOTICE:

if the engine runs with the drive belt loose, the drive belt can slip and cause the engine to overheat or the

battery to receive insufficient charge.

1. Check the drive belt for correct tension, wear and/or

damage. Inspect the drive belt for chunking. Chunk-
ing is defined as a section of the rib missing. Replace
the drive belt if a section longer than

10 mm

(

0.4 in

) is

chunked out.

LEIL18WHL1186AA

1

721G

LEIL18WHL1168AA

2

821G

7-86

Summary of Contents for 721G Stage IV











































































































































































































































































































































































































































































































































Reviews:

No comments

Brands by name

Popular brands

Load more brands