manualshive.com logo in svg

Case 721G Stage IV, Operator'S Manual

Share
Download
Case 721G Stage IV Operator'S Manual Download Page 381

7 - MAINTENANCE

Engine coolant - Change

WARNING

Burn hazard!
Hot coolant can spray and scald if you remove the radiator or deaeration tank cap while the system
is hot. To remove the cap: allow the system to cool, turn the cap to the first notch, and wait for all
pressure to release. Remove the cap only after all pressure has released.
Failure to comply could result in death or serious injury.

W0367A

WARNING

Rotating parts!
The engine is running. Keep clear of rotating fans and belts.
Failure to comply could result in death or serious injury.

W0275A

Drain, flush and change the engine coolant every 4000 hours of operation or each year, whichever occurs first. Clean
the system and change the engine coolant if it becomes dirty or is rust colored.

Prior operation:

Keep all non-authorized personnel clear of the area. Park the machine on a firm, level surface in neutral with the
parking brake applied. Lower the bucket/attachment to the ground. Turn off the engine. Install the transport/service
link into the locked position.

Service specifications

Type of coolant

CASE AKCELA ACTIFULL™ OT EXTENDED LIFE
COOLANT

721G capacity

28.4 L

(

30 US qt

)

821G capacity

30 L

(

31.7 US qt

)

1. After the engine has cooled and the temperature of the

coolant has reached a safe level, remove the cap of the
engine radiator on the left-hand side.

RCPH10WHL139AAH

1

2. Remove the remote drain cover to access the radiator

drain (if equipped).

LEIL17WHL1597AB

2

7-143

Summary of Contents for 721G Stage IV











































































































































































































































































































































































































































































































































Reviews:

No comments

Brands by name

Popular brands

Load more brands