manualshive.com logo in svg

Case 721G Stage IV, Operator'S Manual

Share
Download
Case 721G Stage IV Operator'S Manual Download Page 233

6 - WORKING OPERATIONS

Joystick steering operation

WARNING

Driving hazard!
Check all controls and safety devices in a safe, open area before starting work.
Failure to comply could result in death or serious injury.

W0248A

WARNING

Driving hazard!
Always use the primary steering when traveling on a public road or highway. The left armrest must be
raised and in a locked position during travel. Do not use joystick steering when traveling on a public
road or highway.
Failure to comply could result in death or serious injury.

W0451A

Joystick steering (optional)

The joystick steering (JSS) allows the operator to steer
the loader using a hand controls located on the left-hand
operator seat armrest. The joystick steering allows for
steering movement at the operator’s fingertips.

Moving the JSS control lever

(1)

right or left steers the

machine in the right or left direction. When the joystick is
released, the JSS control lever

(1)

will return to the neutral

(center) position automatically while leaving the machine
articulated in the current position.

The use of these controls are intended for short cycle,
repetitive, high production load and carry operations to
reduce operator fatigue and increase operating efficiency.
The system is set up so that the steering wheel is always
usable (it always has priority).
The JSS is not deactivated with steering wheel use. When
the steering wheel is used, the JSS no longer has control.
As soon as the steering wheel is no longer being turned,
the operator is able to go back to using the joystick without
having to reactivate it.
The joystick steering switch

(2)

is located on the joystick

steering console.
Lift the left-hand armrest to the vertical position to disable
the JSS.

LEIL16WHL1403AB

1

1. Joystick steering (JSS) control lever
2. Joystick steering (JSS) switch

6-11

Summary of Contents for 721G Stage IV











































































































































































































































































































































































































































































































































Reviews:

No comments

Brands by name

Popular brands

Load more brands