![background image](http://html.mh-extra.com/html/carrier/apollo-control-50hjq004-016/apollo-control-50hjq004-016_product-data_2563383013.webp)
13
OPTIONS AND ACCESSORIES (CONT)
See Accessory Performance Data for accessory details.
Carrier
PremierLink
™
controls
are
available
as
a
factory-installed option or as a field-installed accessory. The
controls can be used to actively monitor and control all modes of
operations.
Roof curbs (horizontal and vertical)
permit installation and
securing of ductwork to curb prior to mounting unit on the curb.
Both 14-in. and 24-in. roof curbs are available as field-installed
accessories.
EconoMi$er IV
is available as a factory-installed option in
vertical supply/return configuration only for unit sizes 003-012.
Vertical or horizontal configuration is available for unit sizes 014
and 016. (EconoMi$er IV is available as a field-installed
accessory for horizontal and/or vertical supply return
configurations.) The EconoMi$er IV is provided with an industry
standard, stand--alone, solid-state controller that is easy to
configure and troubleshoot. The EconoMi$er IV is compatible
with non-DDC applications. EconoMi$er IV is equipped with a
barometric relief damper capable of relieving up to 100% return
air. Dry bulb outdoor-air temperature sensor is provided as
standard. The return air sensor, indoor enthalpy sensor, and
outdoor enthalpy sensor are provided as field-installed accessories
to provide enthalpy control, differential enthalpy control, and
differential dry bulb temperature control.
EconoMi$er2
is available as a factory-installed option in vertical
supply/return configuration only. (EconoMi$er2 is available as a
field-installed accessory for horizontal and/or vertical supply
return configurations.) The EconoMi$er2 is provided without a
controller for use with factory-installed PremierLink
™
controls or
field-installed third-party controls. EconoMi$er2 is equipped with
a barometric relief damper capable of relieving up to 100% return
air. Dry bulb outdoor-air temperature sensor is provided as
standard. The enthalpy, differential temperature (adjustable), and
differential enthalpy control are provided as field-installed
accessories. The EconoMi$er2 is capable of control from a 4 to
20 mA signal through optional 4 to 20 mA design without
microprocessor control (required for PremierLink or third party
control interface).
Manual outdoor-air damper
accessory can be preset to admit
up to 50% outdoor air for year round ventilation.
Two-position damper
package is available as an accessory. Both
25% or 100% outdoor air dampers are available.
Head pressure control
(Motormaster) accessory package
maintains condensing temperature between 90
_
F and 110
_
F at
outdoor ambient temperatures down to –20
_
F by condenser-fan
speed modulation or condenser-fan cycling and wind baffles.
Electric resistance heaters
are one stage per heater module.
Single point kits are required, as specified, to meet NEC and UL
requirements.
Unit-mounted, non-fused disconnect switch
provides unit
power shutoff. The switch is accessible from outside the unit and
provides power off lockout capability and is available as
factory-installed option.
Convenience outlet
is factory-installed and internally mounted
with easily accessible 115-v female receptacle for temporary use
of service tools. The device connects to the load--side of the
disconnect. For a line--side convenience outlet, contact your local
Carrier representative.
Compressor cycle delay
(Time Guard II) prevents unit from
restarting for minimum of 5 minutes after shutdown.
Thru-the-bottom
utility
connectors
permit
electrical
connections to be brought to the unit through the basepan.
Connectors are a field-installed accessory.
Fan/filter status switch
accessory provides status of indoor
(evaporator) fan (ON/ OFF) or filter (CLEAN/DIRTY).
62AQ Energy$Recycler
heat pump unit recovers energy from
building exhaust air and pre-conditions ventilation air to allow
higher ventilation requirements and minimizing energy cost.
Energy$Recycler unit is a field-installed accessory.
Energy recovery ventilator
is a wheel device that recovers
energy from the building exhaust air and preconditions
ventilation air. The 62M is a field--installed accessory.
Power exhaust
accessory will provide system exhaust of up to
100% of return air (vertical only). The power exhaust is a
field-installed accessory (separate vertical and horizontal design).
Ultra-violet germicidal lamps
eliminate odor causing mold and
fungus that may develop in the wet area of the evaporator section
of the unit. The high output, low temperature germicidal lamps
are field installed in the evaporator section of the unit, aimed at
the evaporator coil and condensate pan.
Hinged panel option
provides hinged access panels for the filter,
compressor, evaporator fan, and control box areas. Filter hinged
panels permit toolless entry for changing filters. Each hinged
panel is permanently attached to the rooftop unit and is a
factory-installed option.
Emergency heat control package
accessory activates auxiliary
heat when necessary if mechanical heating is locked out.
50
TF
Q
,H
JQ
.H
E
Q
Summary of Contents for APOLLO CONTROL 50HJQ004-016
