63
SENSORY/ACCESSORY
INSTALLATION
There are a variety of sensors and accessories available
for the RTU-OPEN. Some of these can be factory or field
installed, while others are only field installable. The
RTU-OPEN controller may also require connection to a
building network system or building zoning system. All
field control wiring that connects to the RTU-OPEN must
be routed through the raceway built into the corner post of
the unit or secured to the unit control box with electrical
conduit. The unit raceway provides the UL required
clearance between high and low-voltage wiring. Pass the
control wires through the hole provided in the corner post,
then feed the wires thorough the raceway to the
RTU-OPEN. Connect the wires to the removable Phoenix
connectors and then reconnect the connectors to the board.
See Fig. 72.
IMPORTANT
: Refer to the specific sensor or accessory
instructions for its proper installation and for rooftop unit
installation refer to base unit installation instructions and
the unit’s wiring diagrams.
ELECTRICAL SHOCK HAZARD
Failure to follow this warning could result in personal
injury, death and/or equipment damage.
Disconnect and lock--out/tagout electrical power
before wiring the RTU--OPEN controller.
!
WARNING
ADDITIONAL RTU--OPEN
INSTALLATION AND
TROUBLESHOOTING
Additional installation, wiring and troubleshooting
information for the RTU--OPEN Controller can be found
in the following manuals:
“Controls, Start--up, Operation
and Troubleshooting Instructions,”
and
“RTU Open
Installation and Start--up Guide.”
Have a copy of these
manuals available at unit start--up.
DO-6
(Dehumidification)
DO-7
(Reversing Valve)
DO-8
(Power Exhaust)
+24 VDC
Input_2 (CO2/RH)
Gnd
+24 VDC
Input_1 (CO2/RH)
Gnd
Input_5 (SMK)
Input_4 (R)
DO
-5 (Y1)
DO
-4 (Y2)
DO
-3 (W1)
DO
-2 (W2)
DO
-1 (G)
Gnd
Input_3 (X)
24 V
A
C IN
Board Power
24 V
A
C
Input_8 (Enthalpy)
AO
-1 (ECON)
Gnd
(OA
T
)
Gnd
(SA
T
)
Configurable Input_8
24 V
A
C
Configurable Input_5
24 V
A
C
Configurable Input_3
24 V
A
C
Input_9 (Humidistat)
24 V
A
C
BACnet, Modbus, or N2
(LON connection J15)
SPT (temp Input)
SPT (common)
SPT (offset input)
*Remove
both for 0-5V
Protocol Selector
J3
J5
(AO-1)
J4
J1
J2
J5
J14
J11
J22
J13
J12
J15
J20
J17
J19
C10818
Fig. 72 -- RTU--Open Control Module
48TC
Summary of Contents for 48TC 04 Series
