90
START--UP, PREMIERLINK
CONTROLS
ELECTRICAL OPERATION HAZARD
Failure to follow this warning could result in personal
injury or death.
The unit must be electrically grounded in accordance
with local codes and NEC ANSI/NFPA 70 (American
National Standards Institute/National Fire Protection
Association.)
!
WARNING
Use the Carrier network communication software to start
up and configure the PremierLink controller.
Changes can be made using the ComfortWORKS
r
software, ComfortVIEW
t
software, Network Service
Tool, System Pilot
t
device, or Touch Pilot
t
device. The
System Pilot and Touch Pilot are portable interface
devices that allow the user to change system set--up and
setpoints from a zone sensor or terminal control module.
During start--up, the Carrier software can also be used to
verify communication with PremierLink controller.
NOTE
: All set--up and setpoint configurations are factory
set and field--adjustable.
For specific operating instructions, refer to the literature
provided with user interface software.
NOTICE
: All set--up and set point configurations are
factory set and field--adjustable.
Refer to
PremierLink
t
Installation, Start--Up and
Configuration
Instructions
.
for
specific
operating
instructions for the controller. Have a copy of this manual
available at unit start--up.
Perform System Check--Out
1. Check correctness and tightness of all power and
communication connections.
2. At the unit, check fan and system controls for proper
operation.
3. At the unit, check electrical system and connections
of any optional electric reheat coil.
4. Check to be sure the area around the unit is clear of
construction dirt and debris.
5. Check that final filters are installed in the unit. Dust
and debris can adversely affect system operation.
6. Verify that the PremierLink controls are properly
connected to the CCN bus.
START--UP, RTU--OPEN CONTROLS
NOTICE
: Refer to the following manuals for additional
installation, wiring and troubleshooting information for
the
RTU--OPEN
Controller.:
“Controls,
Start--up,
Operation and Troubleshooting Instructions,” “RTU Open
Installation and Start--up Guide” and “RTU--Open
Integration Guide”
. Have a copy of these manuals
available at unit start--up.
FASTENER TORQUE VALUES
Table 38 – Torque Values
Supply fan motor mounting
120 in---lbs (13.6 Nm)
12 in---lbs (1.4Nm)
Supply fan motor adjustment plate
120 in---lbs (13.6 Nm)
12 in---lbs (1.4Nm)
Motor pulley setscrew
72 in---lbs (8.1 Nm)
5 in---lbs (0.6 Nm)
Fan pulley setscrew
72 in---lbs (8.1 Nm)
5 in---lbs (0.6 Nm)
Blower wheel hub setscrew
72 in---lbs (8.1 Nm)
5 in---lbs (0.6 Nm)
Bearing locking collar setscrew
50 in---lbs (6.2 Nm) ---60 in---lbs (6.8 Nm)
Compressor mounting bolts
65 in---lbs (7.3 Nm) ---75 in---lbs (8.5Nm)
Condenser fan motor mounting bolts
20 in---lbs (2.3 Nm)
2 in---lbs 0.2 Nm)
Condenser fan hub setscrew
84 in---lbs (9.5 Nm)
12 in---lbs (1.4 Nm)
48TC
Summary of Contents for 48TC 04 Series
