14
OUTLET
INLET
PUSHRODS
DIAPHRAGM
NEEDLE
VALVE
SPRING
DISTRIBUTOR
FEEDER TUBES
CAPILLARY TUBE
COIL
BULB
EXTERNAL EQUALIZER TUBE
C12046
Fig. 18 -- Thermostatic Expansion Valve (TXV) Operation
Replacing TXV
PERSONAL INJURY HAZARD
Failure to follow this caution can result in injury to
personnel and damage to components..
Always wear approved safety glasses, work gloves
and
other
recommended
Personal
Protective
Equipment (PPE) when working with refrigerants.
CAUTION
!
1. Disconnect all AC power to unit. Use approved
lockout/tagout procedures.
2. Using gauge set approved for use with Puron
(R--410A) refrigerant, recover all refrigerant from the
system..
3. Remove TXV support clamp.
4. Disconnect the liquid line at the TXV inlet.
5. Remove the TXV from the distributor.
6. Remove equalizer tube from suction line of coil. Use
tubing cutter to cut brazed equalizer line
approximately 2--inches (50 mm) above the suction
tube.
7. Remove bulb from vapor tube above the evaporator
coil header outlet.
8. Install the new TXV avoiding damage to the tubing
or the valve when attaching the TXV to the distribut-
or. Protect the TXV against over--temperature condi-
tions y using wet rags and directing the torch flame
tip away from the TXV body. Connect the liquid line
to the TXV inlet by repeating the above process.
9. Route equalizer tube through suction connection
opening (large hole) in fitting panel and install fitting
panel in place.
10. Attach the equalizer tube to the suction line. If the
replacement TXV has a flare nut on its equalizer line,
use a tubing cutter to remove the mechanical flare
nut from the equalizer. Then use a coupling to braze
the equalizer line to the stub (previous equalizer line)
in the suction line.
11. Attach TXV bulb in the same location as the original
(in the sensing bulb indent). See Fig. 20.
12. Wrap the bulb in protective insulation and secure us-
ing the supplied bulb clamp. See Fig. 19.
DIRECTION OF
REFRIGERANT FLOW
EQUALIZER TUBE
FROM TXV VALVE
CAPILLARY TUBE
TO TXV
15.9 mm
(REF)
TXV SENSOR BULB
SENSOR BULB
INDENT
SENSOR BULB
INSULATION
C12556
Fig. 19 -- TXV Sensor Bulb Insulation
13. Sweat the inlet of TXV marked “IN” to the liquid
line. Avoid excessive heat which could damage the
TXV valve.
14. Check for leaks.
15. Evacuate system completely and then recharge by
weight without powering on the compressor.
16. Remove lockout/tagout on main power switch and
restore power to unit.
17. Complete charging procedure.
48TC
Summary of Contents for 48TC 04 Series
