background image

Please read and save these instructions. Read carefully before attempting to assemble, install, operate or maintain the product described. Protect 
yourself and others by observing all safety information. Failure to comply with instructions could result in personal injury and/or property damage! 
Retain instructions for future reference.

Engine Driven 
Centrifugal Pump

Description

 The Wayne pumps are general use 
centrifugal water pumps. The pump is 
equipped with a Viton

®

 seal assembly 

that is also compatible with many 
agricultural chemicals.

Safety Guidelines

This manual contains information that is 
very important to know and understand. 
This information is provided for SAFETY 
and to PREVENT EQUIPMENT PROBLEMS. 
To help recognize this information, 
observe the following symbols.

 

Danger indicates an 

 imminently 

hazardous 

situation which, if not avoided, WILL 
result in death or serious injury.
 

Warning indicates a 

 potentially 

hazardous 

situation which, if not avoided, COULD 
result in death or serious injury.
 

Caution indicates a 

  potentially minor or 

moderate injury.
 Notice 

indicates 

 important 

information, that if not followed, may 
cause damage to equipment.

General Safety 
Information

 CALIFORNIA PROPOSITION 65

 

This product or its 

  power cord may 

contain chemicals known to the State 
of California to cause cancer and birth 
defects or other reproductive harm. Wash 
hands after handling.

1.   Know the pump application, 

limitations, and potential hazards. 
Read these rules and the instructions 
carefully. Failure to follow them could 
cause serious bodily injury and/or 
property damage.

 Never 

run

 engine 

in

an enclosed area. Exhaust 
gases contain deadly 
poisonous carbon monoxide, 
which has no odor or taste.

 

Do not use 

 

 to pump 

flammable or  explosive fluids 
such as gasoline, fuel oil, 
kerosene, etc.  Do not use in 
flammable and/or explosive atmospheres. 
Pump should only be used with liquids 
compatible with pump component materials. 
Failure to follow this warning can result in 
personal injury and/or property damage.

2.  Observe all safety precautions for the 

handling of the fuel.

 Do 

not 

 refuel 

a

hot engine. Fuel spilled on a 
hot engine could result in a 
fire or explosion. Do not 
refuel a running engine.

3.  Pump should be located and should 

rest on a level solid foundation. Do 
not suspend pump by means of the 
discharge pipe.

 

Be sure pump is on 

  secure footing so it 

doesn’t fall over.

4.  Do not use torches or apply excessive 

heat, fire or flames to this pump as an 
explosion may result.

5.  Before working on the unit, insulate 

the wire from the spark plug, by 
disconnecting the spark plug wire from 
the spark plug.

 Complete 

pump and 

 piping 

system 

MUST be protected against below freezing 
temperature. Failure to do so could cause 
serious damage and voids the warranty.

6. 

Do not run pump dry. Water is 
required to lubricate the shaft seal.

7.  Pumping chemicals or corrosive liquids 

with this pump may shorten the life of 
the pump and may be hazardous to the 
operator.

8. Personal 

Safety:

a. Wear safety glasses at all times when 

working with pumps.

b. Keep work area clean, uncluttered 

and properly lighted; replace all 
unused tools and equipment.

c. Keep visitors at a safe distance from 

the work area.

d. Make workshop child-proof with 

padlocks, master switches, and by 
removing starter keys. 

9.  This pump is designed for non-abrasive 

fluid transfer; do not use as a trash 
pump. Always use a suction strainer with 
this pump to filter abrasive material. 
Abrasive materials such as sand and 
gravel will shorten the life of the pump.

Installation

This pump is designed to be self-priming 
when installed and operated as specified 
below.

1.  The pump should be placed as close as 

possible to the water being pumped. 
A pump with 20 foot suction lift will 
not remove water as quickly as a pump 
with 5 foot suction lift (Figure 1).

 Operating Instructions and Replacement Parts List

GPS400

 See Warranty on page 8 for important information about commercial use of this product.

REMINDER: Keep your dated proof of purchase for warranty purposes! 

Attach it to this manual or fi le it for safekeeping.

 © 2010 WAYNE Pumps

320604-001 8/10

Q

UA

LIT

Y

A

SSURANCE

P

ROG

RA

M

Need

Assistance?

Call Us First!

1-800-237-0987

 For parts, product & service information

visit

 www.waynepumps.com

Figure 1

20 Ft. Suction Lift

5 Ft. 

Suction 

Lift

Summary of Contents for 320604-001









Reviews: