CareFusion Alaris SE 7130 Directions For Use Manual Download Page 6

1000DF00480 Issue 2                 5/48               

Symbol Definitions

Labelling Symbols:

Symbol

Description

w

Attention (Consult accompanying document)

Y

Consult accompanying document

x

Potential Equalisation (PE) Connector

k

Type CF applied part. (Degree of protection against electrical shock)

l

Defibrillation-proof Type CF applied part. (Degree of protection against electrical shock)

IPX1

Protected against vertically falling drops of water

s

Device complies with the requirements of Council Directive 93/42/EEC as amended by 2007/47/EC.

T

Date of Manufacture

t

Manufacturer

B

Not for Municipal Waste

e

Functional Earth

    

RS 232

RS232 / Nurse Call Connector

Canadian and U.S. Certification Mark: Products bearing this mark have been tested and certified in accordance 

with applicable U.S. and Canadian electrical safety and performance standards.

X

U.S. Certification Mark: Products bearing this mark have been tested and certified in accordance with applicable 

Federal Communications Comission Guidelines.

A

Flow Sensor receptacle, Channel A

B

Flow Sensor receptacle, Channel B

EC REP

Authorised representative in the European Community

Summary of Contents for Alaris SE 7130



















































Reviews: