Cardin Elettronica 100/SLX1524, Manual

Page: 16 / 56

16
Manual release is to be carried out with the motor Stopped. To release the gate use
the manual release key supplied with the unit. The key should be kept in an easily
accessible place.
SCREW OPERATED MANUAL RELEASE SYSTEM
To release the unit (fig. 8)
1. Lower the lock protection “ A ” on the release knob, insert the key “ B ” and rotate
it through 180 degrees clockwise. The knob is now free and can be rotated.
2. Rotate the knob “ C ” clockwise until reaches its travel limit. The geared motor is
now released and the gate can be moved manually.
Attention!
Do not force the knob to exceed the travel limit.
To relock the unit (fig. 8)
1. Rotate the knob “ D ” anticlockwise until it blocks completely.
Attention!
Do not force the knob to exceed the travel limit.
2. Rotate the key anticlockwise and position the lock protection.
The geared motor is now locked and the gate may be used normally.
Once the system is running normally store the key in a safe place.
Attention! Never use the manual release mechanism while the gate
is in operation.
Moving the gate manually will force the encoder to lose the position
of the gate. To reset the control, once the gate has been relocked,
you will need to give 3 or more movement commands so that the gate
leaf will reach the travel limit enough times to position itself correctly.
Access to the electronic card
Attention! Before opening the cover make
sure that the power has been switched off
at the mains.
To access the motor loosen the two
screws " A " positioned on either end of the
cover as indicated in figure 9.
Electronic programmer for a dc motor with an incorporated radio receiver card, which
allows the memorisation of
300 user codes
(see "remote control" page 20). The
"rolling code" type decoder uses
433.92 MHz
series transmitters.
The motor rotation speed is electronically controlled, starting slowly and increasing
in speed; the speed is reduced as it nears the travel limit so as to enable a controlled
smooth stop.
Programming is carried out using one button and allows you to set the system, the
current sensor and the entire gate travel distance while the logic carries out position
control using an encoder.
The intervention of the anticrush/antidrag sensor during the closing and opening
stages causes a brief ( 10 cm ) travel direction inversion then a block.
Attention!
There is no
230 Vac
contact on any part of the electronic card:
only low voltage safety current is available.
In conformity with the electrical safety standards it is forbidden to connect
binding posts 9 and 10 directly to a circuit that receives power greater
than 30 Vac/dc .
Warning! For the correct operation of the programmer the incorporated
batteries must be in good condition: the programmer will
lose the posi-
tion of the gate in case of blackouts when the batteries are flat the alarm
will sound.
Check the good working order of the batteries every six months (see page
19 "Battery check" ).
• After having installed the device, and before powering up the program-
mer
, release the door (manual release mechanism) and move it manually,
checking that it moves smoothly and has no unusual points of resistance.
• The controlled load output (binding post 15) is aimed at reducing battery
power consumption (if installed) during blackouts; photocells and other
safety devices should be connected to this output.
• When a command is received, via radio or via wire, the electronic program-
mer routes voltage to the CTRL 24 Vdc output. It then evaluates the state
of the safety devices and if they are at rest it will activate the motor.
• Connecting devices to the controlled output contact also allows you to
carry out the autotest function (enabled using "TEST FI" and "TEST FS" in
the "OPTIONS" menu) and check that the safety devices are functioning
correctly.
• The presence of the electrical current sensor does not dispense with the
obligation to install photoelectric cells and other safety devices foreseen
by the safety standards in force.
• Before connecting the appliance make sure that the voltage and frequency
rated on the data plate conform to those of the mains supply.
• For the 230 Vac power supply only use a 2 x 1.5 mm
2
+ cable.
• The cable may only be replaced by qualified technicians.
• An all pole trip switch with at least 3 mm between the contacts must be
installed between the unit and the mains supply.
• Don't use cables with aluminium conductors; don't solder the ends of
cables which are to be inserted into the binding posts; use cables marked
T min 85°C and resistant to atmospheric agents.
• The terminal wires must be positioned in such a way that both the wire
and the insulating sheath are tightly fastened (a plastic jubilee clip is suf-
ficient).
Mains power supply connection
• Connect the control and security device wires.
• Run the mains power supply through the cable clamp located on the bottom right
of the main circuit board and to the separate 3-way terminal board:
- connect the neutral to binding post
N
- connect the earth to binding post
- connect the
live
to binding post
L
MANUAL MANOEUVRE WITH THE MOTOR RELEASED ELECTRONIC PROGRAMMER
IMPORTANT REMARKS
SCALA: 1:2
Prodotti
SL1524SB
13-11-2008
DI0520
Description :
Product Code :
Date :
Drawing number :
P.J.Heath
CARDIN ELETTRONICA S.p.A - 31020 San Vendemiano (TV) Italy - via Raffaello, 36 Tel: 0438/401818 Fax: 0438/401831
Draft :
All rights reserved. Unauthorised copying or use of the information contained in this document is punishable by law
Sblocco carter SL1524SB
A
9
N
L
Fissaggio placca inferiore
06-03-95
DI0286
Description :
Product Code :
Date :
Drawing number :
P.J.Heath
CARDIN ELETTRONICA S.p.A - 31020 San Vendemiano (TV) Italy - via Raffaello, 36 Tel: 0438/401818 Fax: 0438/401831
Draft :
All rights reserved. Unauthorised copying or use of the information contained in this document is punishable by law
Collegamento motore
Sblocco nuovo “A”
SL1524SB
13-11-2008
DM0801
Description :
Product Code :
Date :
Drawing number :
P.J.Heath
CARDIN ELETTRONICA S.p.A - 31020 San Vendemiano (TV) Italy - via Raffaello, 36 Tel: 0438/401818 Fax: 0438/401831
Draft :
All rights reserved. Unauthorised copying or use of the information contained in this document is punishable by law
SL1524SB
A
Sblocco nuovo “B”
SL1524SB
13-11-2008
DM0802
Description :
Product Code :
Date :
Drawing number :
P.J.Heath
CARDIN ELETTRONICA S.p.A - 31020 San Vendemiano (TV) Italy - via Raffaello, 36 Tel: 0438/401818 Fax: 0438/401831
Draft :
All rights reserved. Unauthorised copying or use of the information contained in this document is punishable by law
SL1524SB
B
180°
Sblocco nuovo “C”
SL1524SB
13-11-2008
DM0803
Description :
Product Code :
Date :
Drawing number :
P.J.Heath
CARDIN ELETTRONICA S.p.A - 31020 San Vendemiano (TV) Italy - via Raffaello, 36 Tel: 0438/401818 Fax: 0438/401831
Draft :
All rights reserved. Unauthorised copying or use of the information contained in this document is punishable by law
SL1524SB
C
Sblocco nuovo “D”
SL1524SB
13-11-2008
DM0804
Description :
Product Code :
Date :
Drawing number :
P.J.Heath
CARDIN ELETTRONICA S.p.A
- 31020 San Vendemiano (TV) Italy - via Raffaello, 36 Tel: 0438/401818 Fax: 0438/401831
Draft :
All rights reserved. Unauthorised copying or use of the information contained in this document is punishable by law
SL1524SB
D
5 - 6 turns
5 - 6 turns
8