Capacity TJ5000 DOT Page 79 Operator'S Handbook Manual Download | Manualshive

Page: 79 / 116

background image

Trailer Jockey Operators Handbook

71

3509
{3}

Sensor Supply 1 Circuit -
Voltage Above Normal or
Shorted to High Source. High
voltage detected at sensor
supply number 1 circuit.

Engine power derate.

100
{1}

Engine Oil Rifle Pressure -
Data Valid but Below Normal
Operational Range - Most
Severe Level. Oil pressure
signal indicates oil pressure is
below the engine protection
critical limit.

Progressive power derate
increasing in severity from
time after alert. If the Engine
Protection Shut down feature
is enabled, engine will shut
down 30 seconds after the red
STOP lamp starts flashing.

97
{15}

Water-In-Fuel Indicator - Data
Valid but Above Nor- mal
Operational Range - Least
Severe Level. Water has been
detected in the fuel filter.

Possible white smoke, loss of
power, or hard starting.

639
{9}

J1939 Datalink - Abnormal
Update Rate. Communication
between the electronic control
module (ECM) and another
device on the SAE J1939 data
link has been lost.

Engine speed will ramp down
and remain at idle.

97
{3}

Water-in-Fuel Indicator Sensor
Circuit - Voltage Above
Normal or Shorted to High
Source. High voltage detected
at the water-in-fuel circuit.

None on performance. No
water-in-fuel warning
available.

97
{4}

Water-in-Fuel Indicator Sensor
Circuit - Voltage Below
Normal or Shorted to Low
Source. Low voltage detected
at the water-in-fuel circuit.

None on performance. No
water-in-fuel warning
available.

100
{2}

Engine Oil Rifle Pressure -
Data Erratic, Intermittent, or
Incorrect. The engine oil
pressure sensor is reading an
erratic value at key-on.

None on performance. No
engine protection for oil
pressure.

Table 4-3 CM2150 System Fault Codes (Cont.)

Fault
Code

Reason

Effect

«
...
77
78
79
80
81
...
»

Summary of Contents for TJ5000 DOT





















































































































Reviews:

No comments

Related manuals for TJ5000 DOT

Brand: Magliner Pages: 6

Kenworth T170 2011

Brand: Paccar Pages: 179

Brand: Kalmar Pages: 59

Brand: Mahindra Pages: 55

MAGLINER H-1054

Brand: U-Line Pages: 2

Brand: Sterling Trucks Pages: 213

Brand: LOADMASTER Pages: 39

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands