Capacity TJ5000 DOT Operator'S Handbook Manual Download Page 67

Page: 67 / 116

Trailer Jockey Operators Handbook

103
{10}

Turbocharger Speed - Invalid
Rate of Change Detected.

Engine power derate.

2789
{15}

Turbocharger Turbine Inlet
Temperature (calculated) -
Data Valid but Above Normal
Range - Least Severe Level.

Engine power derate.

2629
{15}

Turbocharger Compressor
Outlet Temperature
(calculated) - Data Valid but
Above Normal Range - Least
Severe Level.

Engine power derate.

027
{13}

EGR Valve Position Failed
Automatic Calibration
Procedure.

Possible low power. Power
removed from the EGR valve
motor.

2791
{3}

EGR Valve Control Circuit -
Shorted High or Open. High
voltage or open circuit
detected at the EGR Valve
Motor Circuit.

Power removed from the EGR
valve motor.

2791
{4}

EGR Valve Control Circuit -
Shorted Low. Low volt- age
detected at the EGR Valve
Motor Circuit.

Power removed from the EGR
valve motor.

2791
{3}

EGR Valve Control Circuit -
Shorted High. High voltage
detected at the EGR Valve
Motor Circuit.

Possible low power. EGR
motor will be powered down.

2791
{6}

EGR Valve Control Circuit -
Excessive Current Detected.
Excessive current detected at
the EGR Valve Motor Circuit.

Possible low power. EGR
motor will be powered down.

2791
{7}

EGR Valve Control -
Mechanical System

not

Responding Properly or Out of
Adjustment. EGR valve

not

responding or slow to respond.

Possible low power. EGR
motor will be powered down.

411
{16}

EGR Differential Pressure
Sensor - Data Valid but Above
Normal Operating Range
Moderately – Severe Level.
EGR differential pressure
sensor failed and automatic
calibration procedure.

EGR valve will be closed.

Table 4-2 CM850 System Fault Codes (Cont.)

Fault
Code

Reason

Effect

Summary of Contents for TJ5000 DOT





















































































































Search results

Summary of Contents for TJ5000 DOT

Reviews:

Brands by name

Popular brands

Capacity TJ5000 DOT, Operator'S Handbook Manual

Search results

Summary of Contents for TJ5000 DOT

Reviews:

Brands by name

Popular brands