background image

Capacity of Texas, Inc.

54

157 
{3}

Injector Metering Rail Number 
1 Pressure Sensor Circuit - 
Shorted High. High signal 
voltage detected at the Rail 
Pressure Sensor Circuit.

Power and/or speed derate.

157
{4}

Injector Metering Rail Number 
1 Pressure Sensor Circuit - 
Shorted Low. Low signal 
voltage detected at the Rail 
Pressure Sensor Circuit.

Power and/or speed derate.

558
{4}

Accelerator Pedal Idle 
Validation Circuit - Shorted 
Low. No voltage detected 
simultaneously on both the 
idle validation off-idle and on-
idle circuits.

Engine will 

only

 idle.

677
{3}

Starter Relay Circuit - Shorted 
High. High voltage detected at 
the Starter Lockout Circuit.

Either the engine will 

not

 start 

or the engine will 

not

 have 

Starter Lockout Protection.

677
{4}

Starter Relay Circuit - Shorted 
Low. Low voltage detected at 
the Starter Lockout Circuit.

Either the engine will 

not

 start 

or the engine will 

not

 have 

Starter Lockout Protection.

103
{16}

Turbocharger Number 1 Speed 
High - Warning Level. High 
turbocharger speed has been 
detected.

Engine power derate. The 
ECM will use an estimated 
turbocharger speed.

167
{16}

Electrical Charging System 
Voltage High - Warning Level. 
High voltage detected by the 
battery voltage monitor 
feature.

Amber Warning Lamp 
illuminated until high battery 
voltage condition is corrected.

167
{18}

Electrical Charging System 
Voltage Low - Warning Level. 
Low voltage detected by the 
battery voltage monitor 
feature.

Amber Warning Lamp 
illuminated until low battery 
voltage condition is corrected.

167
{1}

Electrical Charging System 
Voltage Low - Critical Level. 
Very low voltage detected by 
the battery volt- age monitor 
feature.

Red Stop Lamp illuminated 
until very low battery voltage 
condition is corrected.

1378
{31}

Change Lubricating Oil and 
Filter.

None on performance. 
Maintenance reminder 

only

.

Table 4-2  CM850 System Fault Codes (Cont.)

Fault 
Code

Reason

Effect

Summary of Contents for TJ5000 DOT





















































































































Reviews: