manualshive.com logo in svg

Capacity TJ5000 DOT, Operator'S Handbook Manual

Share
Download
Capacity TJ5000 DOT Operator'S Handbook Manual Download Page 63

Trailer Jockey Operators Handbook

55

103
{18}

Turbocharger Number 1 Speed 
Low - Warning Level. Low 
turbocharger speed has been 
detected

Engine power derate. The 
ECM will use an estimated 
turbocharger speed.

190
{2}

Primary Engine Speed Sensor 
Error.

Engine power derate.

1172
{3}

Turbocharger Number 1 
Compressor Inlet Temperature 
Sensor Circuit - Shorted High. 
High signal voltage detected at 
the Turbocharger Compressor 
Inlet Air Temperature Sensor 
Circuit.

Engine power derate.

1172
{4}

Turbocharger Number 1 
Compressor Inlet Temperature 
Sensor Circuit - Shorted Low. 
Low signal voltage detected at 
the Turbocharger Compressor 
Inlet Air Temperature Sensor 
Circuit.

Engine power derate.

723
{7}

Engine Speed/Position 
Number 2 - Mechanical 
Misalignment Between 
Camshaft and Crankshaft 
Sensors. Engine position 
signal from the engine speed 
sensor and camshaft position 
sensor do 

not

 match.

Engine power derate.

723
{2}

Secondary Engine Speed 
Sensor Error. The ECM has 
detected an error in the 
camshaft position sensor 
signal.

Engine power derate.

1590
{2}

Loss of Communication with 
Adaptive Cruise Control.

Adaptive Cruise Control will 

not

 operate.

166 
{2}

Cylinder Power imbalance 
Between Cylinders. A power 
imbalance between cylinders 
was detected by the ECM.

Engine could possibly have a 
rough idle or misfire.

Table 4-2  CM850 System Fault Codes (Cont.)

Fault 
Code

Reason

Effect

Summary of Contents for TJ5000 DOT





















































































































Reviews:

No comments

Brands by name

Popular brands

Load more brands