Capacity TJ5000 DOT Page 100 Operator'S Handbook Manual Download

Page: 100 / 116

Capacity of Texas, Inc.

P0123

Pedal Position Sensor
High Voltage

Use default throttle values.
Freezes shift adapts.

P0218

Transmission Fluid
Over Temperature

Use hot mode shift
schedule. Holds fourth
range. TCC is inhibited.

P0602

TCM Not Programmed

Yes

Lock in Neutral

P0610

TCM Vehicle Options

Yes

Use TID A calibration

P0613

TCM Processor

All solenoids off

P0614

Torque Control Data
Mismatch—ECM/

Yes

Allows operation only in
reverse and second range.

P0634

TCM Internal

Yes

SOL OFF (hydraulic

P063E

Auto Configuration

Yes

Use default throttle values

P063F

Auto Configuration
Engine Coolant Temp

None

P0658

Actuator Supply

Yes

DNS, SOL OFF (hydraulic

P0659

Actuator Supply

Yes

DNS, SOL OFF (hydraulic

P0702

Transmission Control

Yes

Uses TID A calibration

P0703

Brake Switch Circuit
Malfunction

No Neutral to Drive shifts
for refuse packer. TCM
inhibits retarder operation
if a TPS code is also
active.

P0708

Transmission Range

Yes

Ignore defective strip

P070C

Transmission Fluid

None

P070D

Transmission Fluid

None

P0711

Transmission Fluid
Temperature Sensor

Yes

Use default sump temp

P0712

Transmission Fluid
Temperature Sensor

Yes

Use default sump temp

P0713

Transmission Fluid
Temperature Sensor

Yes

Use default sump temp

P0716

Turbine Speed Sensor

Yes

DNS, Lock in current

P0717

Turbine Speed Sensor

Yes

DNS, Lock in current

Table 4-4 Transmission Diagnostic Codes (Cont.)

Code

Description

Check

Trans

Light

Description

Summary of Contents for TJ5000 DOT





















































































































Search results

Summary of Contents for TJ5000 DOT

Reviews:

Related manuals for TJ5000 DOT

Brands by name

Popular brands

Capacity TJ5000 DOT, Operator'S Handbook Manual

Search results

Summary of Contents for TJ5000 DOT

Reviews:

Related manuals for TJ5000 DOT

Brands by name

Popular brands