Canon PIXMA MX860 series, Service Manual

Page: 18 / 106

RTP, RTN has been received.
##290 TX After MPS transmission, a signal other than PIN, PIP, MCF,
RTP, RTN has been received.
##670 TX In V.8 late start, the DIS V.8 ability from the receiving
machine was detected, and CI was sent in response; however,
the procedure failed, causing T1 time-over. - In bit 0 of the service data #1 SSSW
SW28, prohibit the V.8 / V.34
procedure of the sending machine.
##671 RX In V.8 call reception, the procedure fails to proceed to phase 2
after CM detection, causing T1 time-over. - In bit 0 of the service data #1 SSSW
SW28, prohibit the V.8 / V.34
procedure of the sending machine.
##672 TX In V.34 transmission, the procedure fails to proceed from
phase 2 to phase 3 or later, causing T1 time-over - In bit 0 of the service data #1 SSSW
SW28, prohibit the V.8 / V.34
procedure of the sending machine.
##673 RX In V.34 reception, the procedure fails to proceed from phase 2
to phase 3 or later, causing T1 time-over - In bit 0 of the service data #1 SSSW
SW28, prohibit the V.8 / V.34
procedure of the sending machine.
##674 TX In V.34 transmission, the procedure fails to proceed from
phase 3 or 4 to the control channel or later, causing T1 time-
over - In bit 0 of the service data #1 SSSW
SW28, prohibit the V.8 / V.34
procedure of the sending machine.
##675 RX In V.34 reception, the procedure fails to proceed from phase 3
or 4 to the control channel or further, causing T1 time-over - In bit 0 of the service data #1 SSSW
SW28, prohibit the V.8 / V.34
procedure of the sending machine.
##750 TX After transmitting PPS-NULL in ECM transmission, no
significant signal has been received, and re-transmission of
the procedure signal has been attempted the number of
specified times but failed. - Try a higher transmission level.
##752 TX After transmitting PPS-NULL in ECM transmission, DCN
has been received. - Try a higher transmission level.
##753 TX After transmitting PPS-NULL in ECM transmission, re-
transmission of the procedure signal has been attempted the
number of specified times but failed, or T5 time-over (60
sec.) has occurred. - Increase the period of time of the T5
time-over.
##754 TX After transmitting PPS-NULL in ECM transmission, re-
transmission of the procedure signal has been attempted the
number of specified times but failed. - Try a higher transmission level.
##755 TX After transmitting PPS-MPS in ECM transmission, no
significant signal has been received, and re-transmission of
the procedure signal has been attempted the number of
specified times but failed. - Try a higher transmission level.
##757 TX After transmitting PPS-MPS in ECM transmission, DCN has
been received. - Try a higher transmission level.
##758 TX After transmitting PPS-MPS in ECM transmission, re-
transmission of the procedure signal has been attempted the
number of specified times but failed, or T5 time-over (60
sec.) has occurred. - Increase the period of time of the T5
time-over.
##759 TX After transmitting PPS-MPS in ECM transmission, re-
transmission of the procedure signal has been attempted the
number of specified times but failed. - Try a higher transmission level.
##760 TX After transmitting PPS-EOM in ECM transmission, no
significant signal has been received, and re-transmission of
the procedure signal has been attempted the number of
specified times but failed. - Try a higher transmission level.
15 / 64