Canon imageRUNNER ADVANCE 6055 Series, Service Manual

Page: 886 / 1406

8
8
8-104
8-104
Service Mode > COPIER > FUNCTION > PART-CHK
Service Mode > COPIER > FUNCTION > PART-CHK
■
PANEL
COPIER > FUNCTION > PANEL
LCD-CHK Check of LCD Panel dot missing
Lv.1 Details To check whether there is a missing dot on the LCD Panel of the
Control Panel.
Use case When replacing the LCD Panel
Adj/set/operate method 1) Select the item, and then press OK key.
2) Check that the LCD Panel lights up in the order of white, black,
red, green and blue.
3) Press STOP key to terminate checking.
LED-CHK Check of Control Panel LED
Lv.1 Details To check whether the LED on the Control Panel lights up.
Use case When replacing the LCD Panel
Adj/set/operate method 1) Select the item, and then press OK key.
2) Check that the LED lights up in the order.
3) Use LED-OFF to terminate checking.
Related service mode COPIER> FUNCTION> PANEL> LED-OFF
LED-OFF End check of Control Panel LED
Lv.1 Details To terminate the check of LED on the Control Panel.
Use case During execution of LED-CHK
Adj/set/operate method Select the item, and then press OK key.
Related service mode
COPIER> FUNCTION> PANEL> LED-CHK
KEY-CHK Check of key entry
Lv.1 Details To check the key input on the Control Panel.
Use case When replacing the LCD Panel
Adj/set/operate method 1) Select the item and press the key on the Control Panel.
2) Check that the input value is displayed.
3) Cancel the selection to terminate checking.
TOUCHCHK Adj of coordinate pstn of Touch Panel
Lv.1 Details To adjust the coordinate position on the Touch Panel of the Control
Panel.
Use case When replacing the LCD Panel
Adj/set/operate method 1) Select the item, and then press OK key.
2) Press the nine “+” keys in sequence.
T-8-46
■
PART-CHK
COPIER > FUNCTION > PART-CHK
CL Specification of operation Clutch
Lv.1 Details To specify the Clutch to operate.
Use case When replacing the Clutch/checking the operation
Adj/set/operate method Enter the value, and then press OK key.
Display/adj/set range
1 to 6
1: Developing Clutch (CL1)
2: Magnet Roller Clutch (CL5)
3 to 6: Not used
Default value 0
Related service mode COPIER> FUNCTION> PART-CHK> CL-ON
CL-ON Operation check of Clutch
Lv.1 Details To start operation check of the Clutch specified by CL.
The operation stops after “ON for 0.5 sec” => “OFF for 10 sec” => “ON
for 0.5 sec” => “OFF for 10 sec” => “ON for 0.5 sec”.
Use case When replacing the Clutch/checking the operation
Adj/set/operate method Select the item, and then press OK key.
Display/adj/set range
During operation: ACTIVE, When operation finished normally: OK!
Default value 0
Required time Approx. 22 seconds
Related service mode COPIER> FUNCTION> PART-CHK> CL
MTR Specification of operation Motor
Lv.1 Details To specify the Motor to operate.
Use case When replacing the Motor/checking the operation
Adj/set/operate method Enter the value, and then press OK key.
Caution
Be sure to remove the Toner Container before Toner Supply Motor
(M10) is activated. If it remains to be installed, toner is supplied.
Display/adj/set range 1 to 16
1: Toner Supply Motor (M10)
2: Toner Feed Motor (M28)
3: Delivery Motor (M13)
4: Reverse Motor (M14)
5: Side Registration Motor (M16)
6: Duplex Feed Right Motor (M18)
7: Duplex Feed Left Motor (M19)
8: Vertical Path Upper Motor (M26)
9: Vertical Path Lower Motor (M27)
10: Vertical Path Middle Motor (M31)
11: Duplex Feed Merging Motor (M32)
12: Multi-purposeTray Registration Front Motor (M33)
13: Registration Motor (M34)
14: ETB Motor (M43)
15 to 16: Not used
Default value 1
Related service mode COPIER> FUNCTION> PART-CHK> MTR-ON