manualshive.com logo in svg

Canon im2520f, Setup Instructions, Page: 84 / 143

Share
Download
Canon im2520f Setup Instructions Download Page 84

9212

– 3 –

4512-7741-02

5. Remove the guide plate (two screws).

4512U009AB

6. Remove the cover (two screws).

4512U010AB

7. Remove the cover (two screws).

4512U011AA

8. Install the Sensor Unit to the cover that has 

been removed in step 7 following the order 
shown in the illustration (by fitting tabs of the 
Sensor Unit into slits in the cover).

9. Slightly press the Sensor Unit in the direction 

shown by the arrow.

4512U012AC

1

2

3

10. Withdraw the connector of the Sensor Unit 

through the hole shown in the illustration.

11. Open the cord clamp.

12. Connect the connector and close the cord 

clamp.

4512U028AB

13. Reinstall the cover (two screws).

4512U014AA

14. Press the Flat Spring against the Finisher 

Unit and install it (one screw).

4512U015AB

15. Insert the Punch Unit.

16. Temporarily secure the Punch Unit (one 

screw).

4512U016AA

4512‑7741‑02.fm  3 ページ  ２００３年１０月３日 金曜日 午前１０時１１分

Summary of Contents for im2520f
















































































































































Reviews:

No comments