manualshive.com logo in svg

Canon im2520f, Setup Instructions, Page: 64 / 143

Share
Download
Canon im2520f Setup Instructions Download Page 64

9219000000

– 3 –

4526-7741-02

8. Move the Fusing Unit as illustrated, unplug the Heater Lamp hookup connector, and 

remove the Fusing Unit from the copier.

■

Removing the Fusing Cover

■

Installing the Fusing Unit

5. Unplug the three connectors of the Hookup 

Harness of the Fusing Cover and that of the 
Fusing Unit.

4625U008AA

6. Remove the Hookup Harness of the Fusing 

Cover from the cord clamp and edge cover.

4625U009AA

7. Remove two Fusing Unit fixing screws.

4625U010AA

4625U012AA

4625U013AA

1. Remove one screw from the Fusing Cover.
2. Unhook the hooks (at three places) on the 

backside of the cover and remove the cover.

4625U014AA

3. Remove the fixing brackets on both sides of 

the Upper Fusing Guide (two screws).

4. Remove the Upper Fusing Guide.
*

The Fusing Cover and Upper Fusing Guide, 
which have been removed, will not be used.

4625U015AA

1. Install the Fusing Unit to the copier (two 

screws).

4625U016AA

2. Connect one Heater Lamp hookup connector 

and two Hookup Harness connectors of the 
Fusing Unit to the mating connectors on the 
copier side.

4625U017AA

4625U018AA

Summary of Contents for im2520f
















































































































































Reviews:

No comments