manualshive.com logo in svg

Canon im2520f, Setup Instructions, Page: 114 / 143

Share
Download
Canon im2520f Setup Instructions Download Page 114

– 5 –

4513-7746-02

3.2 Installing the Network Interface Card (

ZC3500090

)

(1) Preparing to install the CLAN circuit board

(2) Installing the CLAN circuit board

1. Attach the card spacer to the MFB3 circuit

board.

C4514U004AA

2. Make sure that the OPE cable is not cov-

ered by the connector for the CLAN circuit
board.

C4514U005AB

3. Affix the CLAN sheet to the

CLAN circuit board.

C4514U006AD

CLAN
sheet

After affixing the CLAN sheet to the CLAN cir-
cuit board, attach the plate.

C4514U014AA

(Only for Europe)

Plate

1. Connect the CLAN circuit board to CN7 on

the MFB3 circuit board.

*

Press the two points indicated with arrows
and marked “PUSH HERE”, and firmly
insert the connectors. (Do not touch any
soldered areas.)

C4514U007AA

2. Secure the CLAN circuit board with 3

screws.

*

Access the screw for step 

➁

 through the slot

between the scanner and the document
cover after opening the document cover.
Tighten the screw for step 

➂

 with the CLAN

finger. (Use a short screwdriver)

C4514U008AB

Tighten with the CLAN finger.

CLAN finger

➁

➀

➂

Summary of Contents for im2520f
















































































































































Reviews:

No comments