Canon GP215 Service Handbook Download Page 181

Page: 181 / 217

7–73

SERVICE MODE

Item

SPCL-PPR

SCAN_SEL

FAX_DOC_FEED

Function

Use it to change thick
paper mode.

Use it if parts of an image
are missing in main scan-
ning direction on large-
size papers when using
the feeder and copying a
non-default original.

use it to switch reading
patterns for RDF-G1 fax
originals.

Description

0: The thick paper mode remains off.
1: Switching the fixing temperature, the thick

paper mode is supported.

2: The fixing temperature is switched so that

paper thicker than that supported under ‘1’
may be supported.
However, for ‘1’ and ‘2’ , the icon for the
special cassette must be registered using
‘ADDITIONAL FUNCTION’ (i.e., the third
icon from the middle row).

0: Nomal copying mode.
7: Priority on paper mode*

*Center reference output prevents missing
images.

0: The topmost page of the stack of originals

will be picked up and read first and dis-
charged on the right.

1: The bottommost page of the stack of origi-

nals will be picked up and read first and
returned to the original tray (same way as
copying).

Summary of Contents for GP215

























































































































































































































Search results

Summary of Contents for GP215

Reviews:

Canon GP215, Service Handbook, Page: 181 / 217

Search results

Summary of Contents for GP215

Reviews: