Canon AXIS 1650 User Manual Download Page 10

Page: 10 / 75

Print Server Installation

AXIS 1650 User’s Manual

Section 5

Print Server Installation

Follow these steps to install and configure your AXIS 1650:

1. Connect the Hardware, on page 10
2. Set the IP Address, on page 11
3. Windows Installation, on page 17

Connect the Hardware

Backside label of print server

1. Make sure that your printer is switched off and that the print server’s

power adapter is disconnected.

2. Locate the

serial number, found on the underside label of the print server,

and write it down. You will need this number to configure the print server.

3. Either connect the printer to the USB port using the USB cable, or connect

the printer directly to the LPT port or use a printer cable.

Note: AXIS 1650 is featured with two ports for ease of integration with

most Canon printers. There is, however, no support for handling two

connected printers simultaneously.

4. Connect the print server to the network using a shielded twisted pair

(category 5) RJ45 cable, 10baseT or 100baseTX.

5. Switch on the printer and make sure it is ready for use.

6. Connect the power adapter to the print server. The power indicator will light

up. When the network indicator starts to flash, the print server is correctly
connected to the network.

Test button

Network indicator

USB Printer Port (USB1)

Power indicator

Power adapter
connector

Ethernet connector

Parallel printer port (LPT1)

Example: If the print server’s serial number

address will be 00-40-8c-18-1c-f0

The print server’s MAC/Ethernet address is
based on its serial number (S/N).

is 00408c181cf0, the Ethernet/MAC

Summary of Contents for AXIS 1650












































































Search results

Summary of Contents for AXIS 1650

Reviews:

Related manuals for AXIS 1650

Brands by name

Popular brands

Canon AXIS 1650, User Manual

Search results

Summary of Contents for AXIS 1650

Reviews:

Related manuals for AXIS 1650

Brands by name

Popular brands